Exam Code: ccnp routing and switching switch 300 115 official cert guide (Practice Exam Latest Test Questions VCE PDF)
Exam Name: Implementing Cisco IP Switched Networks
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass ccnp switch 300 115 Exam.
Q51. Which command is needed to enable DHCP snooping if a switchport is connected to a DHCP server?
A. ip dhcp snooping trust
B. ip dhcp snooping
C. ip dhcp trust
D. ip dhcp snooping information
Answer: A
Q52. Which four LACP components are used to determine which hot-standby links become active after an interface failure within an EtherChannel bundle? (Choose four.)
A. LACP system priority
B. LACP port priority
C. interface MAC address
D. system ID
E. port number
F. hot-standby link identification number
G. interface bandwidth
Answer: ABDE
Q53. For client server failover purposes, the application server team has indicated that they must not have the standard 30 second delay before their switchport enters a forwarding state. For their disaster recovery feature to operate successfully, they require the switchport to enter a forwarding state immediately. Which spanning-tree feature satisfies this requirement?
A. Rapid Spanning-Tree
B. Spanning-Tree Timers
C. Spanning-Tree FastPort
D. Spanning-Tree PortFast
E. Spanning-Tree Fast Forward
Answer: D
Q54. Which portion of AAA looks at what a user has access to?
A. authorization
B. authentication
C. accounting
D. auditing
Answer: A
Q55. Refer to the exhibit.
All ports are members of VLAN 10. Considering the default cost of upstream bridges to the root bridge is equal, which option will be the new root port for VLAN 10?
A. interface f0/13
B. interface f0/14
C. interface f0/15
D. interface f0/21
Answer: D
Q56. Which statement describes what happens if all VSL connections between the virtual switch
members are lost?
A. Both virtual switch members cease to forward traffic.
B. The VSS transitions to the dual active recovery mode, and both virtual switch members continue to forward traffic independently.
C. The virtual switch members reload.
D. The VSS transitions to the dual active recovery mode, and only the new active virtual switch continues to forward traffic.
Answer: D
Q57. Refer to the exhibit.
Which option describes the reason for this message in a GLBP configuration?
A. Unavailable GLBP active forwarder
B. Incorrect GLBP IP address
C. HSRP configured on same interface as GLBP
D. Layer 2 loop
Answer: D
Q58. Refer to the exhibit.
A network engineer wants to analyze all incoming and outgoing packets for an interface that is connected to an access switch. Which three items must be configured to mirror traffic to a packet sniffer that is connected to the distribution switch? (Choose three.)
A. A monitor session on the distribution switch with a physical interface as the source and the remote SPAN VLAN as the destination
B. A remote SPAN VLAN on the distribution and access layer switch
C. A monitor session on the access switch with a physical interface source and the remote SPAN VLAN as the destination
D. A monitor session on the distribution switch with a remote SPAN VLAN as the source and physical interface as the destination
E. A monitor session on the access switch with a remote SPAN VLAN source and the physical interface as the destination
F. A monitor session on the distribution switch with a physical interface as the source and a physical interface as the destination
Answer: BCD
Q59. A network engineer has just deployed a non-Cisco device in the network and wants to get information about it from a connected device. Cisco Discovery Protocol is not supported, so the open standard protocol must be configured. Which protocol does the network engineer configure on both devices to accomplish this?
A. IRDP
B. LLDP
C. NDP
D. LLTD
Answer: B
Q60. refer to the exhibit.
f1/0 and f1/1 have the same end-to-end path cost to the designated bridge. Which action is needed to modify the Layer 2 spanning-tree network so that traffic for PC1 VLAN from switch SW3 uses switchport f1/1 as a primary port?
A. Modify the spanning-tree port-priority on SW1 f1/1 to 0 and f1/0 to 16.
B. Modify the spanning-tree port-priority on SW1 f1/1 to 16 and f1/0 to 0.
C. Modify the spanning-tree port-priority on SW2 f1/1 to 0 and f1/0 to 16.
D. Modify the spanning-tree port-priority on SW2 f1/1 to 16 and f1/0 to 0.
Answer: C