Master the examcollection 300 115 SWITCH Implementing Cisco IP Switched Networks content and be ready for exam day success quickly with this Pass4sure ccnp switch 300 115 dumps exam guide. We guarantee it!We make it a reality and give you real ccnp switch 300 115 dumps pdf questions in our Cisco 300 115 switch pdf braindumps.Latest 100% VALID Cisco 300 115 pdf Exam Questions Dumps at below page. You can use our Cisco ccnp switch 300 115 labs braindumps and pass your exam.

P.S. Actual 300-115 guidance are available on Google Drive, GET MORE: https://drive.google.com/open?id=1WzeEi-YMJ4-9dZHT1BGDd5p41JZ_7zCq


New Cisco 300-115 Exam Dumps Collection (Question 4 - Question 14)

Q4. A network administrator configures 10 extended VLANs ranging from VLANs 3051 to 3060 in an enterprise network. Which version of VTP supports these extended VLANs?

A. version 1

B. version 2

C. version 3

D. VTP does not recognize extended VLANs.

Answer: C


Q5. A network engineer configured an Ethernet switch using these commands.

Switchone(config) # Spanning-tree portfast bpdufilter default

Which statement about the spanning-tree portfast feature on the switch is true?

A. If an interface is enabled for portfast receives BDPU, the port goes through the spanning-tree listening, learning, and forwarding states.

B. If an interface is enabled for portfast receives BDPU, the port does not go through the spanning-tree listening, learning, and forwarding states.

C. If an interface is enabled for portfast receives BDPU, the port is shut down immediately.

D. If an interface is enabled for portfast receives BDPU, the port goes into the spanning- tree inconsistent state.

Answer: A


Q6. What is the maximum number of virtual MAC addresses that GLBP allows per group?

A. 2

B. 4

C. 6

D. 8

Answer: B


Q7. For security reasons, the IT manager has prohibited users from dynamically establishing trunks with their associated upstream switch. Which two actions can prevent interface trunking? (Choose two.)

A. Configure trunk and access interfaces manually.

B. Disable DTP on a per interface basis.

C. Apply BPDU guard and BPDU filter.

D. Enable switchport block on access ports.

Answer: A,B


Q8. What is the function of NSF?

A. forward traffic simultaneously using both supervisors

B. forward traffic based on Cisco Express Forwarding

C. provide automatic failover to back up supervisor in VSS mode

D. provide nonstop forwarding in the event of failure of one of the member supervisors

Answer: D


Q9. Refer to the exhibit.

A network engineer investigates a recent network failure and notices that one of the interfaces on the switch is still down. What is causing the line protocol on this interface to be shown as down?

A. There is a layer 1 physical issue.

B. There is a speed mismatch on the interface.

C. The interface is configured as the target of the SPAN session.

D. The interface is configured as the source of the SPAN session.

E. There is a duplex mismatch on the interface.

Answer: C


Q10. Regarding high availability, with the MAC address 0000.0c07.ac03, what does the u201c03u201d represent?

A. The GLBP group number

B. The type of encapsulation

C. The HSRP router number

D. The VRRP group number

E. The HSRP group number

F. The active router number

Answer: E


Q11. Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRP to provide a high availability solution.

u2022 DSW1 -primary device for VLAN 101 VLAN 102 and VLAN 105

u2022 DSW2 - primary device for VLAN 103 and VLAN 104

u2022 A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.

Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.

All interfaces are active. DSW2 has not become the active device for the VLAN 103 HSRP group. As related to the VLAN 103 HSRP group, what can be done to make the group function properly?

A. On DSW1, disable preempt.

B. On DSW1, decrease the priority value to a value less than 190 and greater than 150.

C. On DSW2, increase the priority value to a value greater 200 and less than 250.

D. On DSW2, increase the decrement value in the track command to a value greater than 10 and less than 50.

Answer: C

Explanation: The reason DSW2 has not become the active switch for Vlan103 is because the priority value of DSW1 is higher than that of DSW2. In order to make DSW2 become the active switch, we need to increase DSW2u2021s priority (to higher than 200) or decrease DSW1u2021s priority (to lower than 190) -> B and C are correct.

But there is another requirement from this question that u201cA failure on gig1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet 1/0/1 on backup device has also failedu201d. This requirement makes answer B incorrect. For example, we choose to decrease the priority value on DSW1 to 160 (according to answer B) then DSW2 will become active switch (that is good). When Gi1/0/1 on DSW2 goes down, the priority of DSW2 will be 190 u2013 50 = 140 < 160 -> DSW1 will become new active switch (it is good, too). But when Gi1/0/1 on DSW1 also goes down, the priority of DSW1 will be 160 u2013 10 = 150 and it is still greater than 140 of DSW2 ->

DSW2 cannot retake the active role as the requirement of this question.


Q12. In a switch stack where is the the SDM template stored?

A. All switches in stack

B. Master switch

C. Flash memory

D. Another

Answer: B


Q13. After an EtherChannel is configured between two Cisco switches, interface port channel 1 is in the down/down state. Switch A is configured with channel-group 1 mode active, while Switch B is configured with channel-group 1 mode desirable. Why is the EtherChannel bundle not working?

A. The switches are using mismatched EtherChannel negotiation modes.

B. The switch ports are not configured in trunking mode.

C. LACP priority must be configured on both switches.

D. The channel group identifier must be different for Switch A and Switch B.

Answer: A


Q14. Which private VLAN access port belongs to the primary VLAN and can communicate with all interfaces, including the community and isolated host ports?

A. promiscuous port

B. isolated port

C. community port

D. trunk port

Answer: A


P.S. Easily pass 300-115 Exam with Allfreedumps Actual Dumps & pdf vce, Try Free: https://www.allfreedumps.com/300-115-dumps.html (416 New Questions)