Cause all that matters here is passing the Cisco 300-410 exam. Cause all that you need is a high score of 300-410 Implementing Cisco Enterprise Advanced Routing and Services (ENARSI) exam. The only one thing you need to do is downloading Testking 300-410 exam study guides now. We will not let you down with our money-back guarantee.
Free demo questions for Cisco 300-410 Exam Dumps Below:
NEW QUESTION 1
Refer to the exhibit.
An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?
- A. Add the aaa authentication login default none command to the global configuration.
- B. Replace the capital “C” with a lowercase “c” in the aaa authentication login Console local command.
- C. Add the aaa authentication login default group tacacs+ local-case command to the global configuration.
- D. Add the login authentication Console command to the line configuration
Answer: D
NEW QUESTION 2
Which transport layer protocol is used to form LDP sessions?
- A. UDP
- B. SCTP
- C. TCP
- D. RDP
Answer: C
NEW QUESTION 3
Refer to the exhibit.
Users report that IP addresses cannot be acquired from the DHCP server. The DHCP
server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day. Which action fixes the issue within the current resources?
- A. Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool
- B. Configure the DHCP lease time to a smaller value
- C. Configure the DHCP lease time to a bigger value
- D. Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool
Answer: B
NEW QUESTION 4
Refer to the exhibit.
An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is the reason for this issue?
- A. By default, only internal routes and external type 1 routes are redistributed into BGP
- B. Only classful networks are redistributed from OSPF to BGP
- C. BGP convergence is slow, so the route will eventually be present in the BGP table
- D. By default, only internal OSPF routes are redistributed into BGP
Answer: A
NEW QUESTION 5
When provisioning a device in Cisco DNA Center, the engineer sees the error message “Cannot select the device. Not compatible with template”.
What is the reason for the error?
- A. The template has an incorrect configuration.
- B. The software version of the template is different from the software version of the device.
- C. The changes to the template were not committed.
- D. The tag that was used to filter the templates does not match the device tag.
Answer: B
NEW QUESTION 6
Refer to the exhibit.
Which configuration denies Telnet traffic to router 2 from 198A:0:200C::1/64?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: A
NEW QUESTION 7
Refer to the exhibit.
Network operations cannot read or write any configuration on the device with this
configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)
- A. Configure SNMP rw permission in addition to community ciscotest.
- B. Modify access list 1 and allow operations subnet in the access list.
- C. Modify access list 1 and allow SNMP in the access list.
- D. Configure SNMP rw permission in addition to version 1.
- E. Configure SNMP rw permission in addition to community ciscotest 1.
Answer: AB
NEW QUESTION 8
Refer to the exhibit.
An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table. Why is the summary route missing?
- A. The summary-address command is used only for summarizing prefixes between areas.
- B. The summary route is visible only in the OSPF database, not in the routing table.
- C. There is no route for a subnet inside 10.0.0.0/8, so the summary route is not generated.
- D. The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.
Answer: A
NEW QUESTION 9
Which statement about IPv6 ND inspection is true?
- A. It learns and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables.
- B. It learns and secures bindings for stateless autoconfiguration addresses in Layer 2 neighbor tables.
- C. It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables.
- D. It learns and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables.
Answer: B
NEW QUESTION 10
Refer to the exhibit.
An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?
- A. Dynamic routing protocols always have priority over static routes.
- B. The metric of the OSPF route is lower than the metric of the static route.
- C. The configured AD for the static route is higher than the AD of OSPF.
- D. The syntax of the static route is not valid, so the route is not considered.
Answer: C
NEW QUESTION 11
Refer to the exhibit.
R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns
the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?
- A. R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
- B. Route reflector setup requires full IBGP mesh between the routers.
- C. In route reflector setup, only classful prefixes are advertised to other clients.
- D. In route reflector setups, prefixes are not advertised from one client to another.
Answer: A
NEW QUESTION 12
Refer to the exhibit.
After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both
spoke-to-spoke and hub were not establishing. Which two actions resolve the issue? (Choose two.)
- A. Change the mode from mode tunnel to mode transport on R3.
- B. Remove the crypto isakmp key cisco address 10.1.1.1 on R2 and R3.
- C. Configure the crypto isakmp key cisco address 192.1.1.1 on R2 and R3.
- D. Configure the crypto isakmp key cisco address 0.0.0.0 on R2 and R3.
- E. Change the mode from mode transport to mode tunnel on R2.
Answer: AD
NEW QUESTION 13
Refer to the exhibit.
What does the imp-null tag represent in the MPLS VPN cloud?
- A. Pop the label
- B. Impose the label
- C. Include the EXP bit
- D. Exclude the EXP bit
Answer: C
NEW QUESTION 14
Refer to the exhibit.
Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?
- A. Issue the eigrp stub command on R1.
- B. Issue the no eigrp stub command on R1.
- C. Issue the eigrp stub command on R2.
- D. Issue the no eigrp stub command on R2.
Answer: A
NEW QUESTION 15
Refer to the exhibit.
During troubleshooting it was discovered that the device is not reachable using a secure web browser. What is needed to fix the problem?
- A. permit tcp port 443
- B. permit udp port 465
- C. permit tcp port 465
- D. permit tcp port 22
Answer: A
NEW QUESTION 16
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 17
Refer to the exhibit.
Which control plane policy limits BGP traffic that is destined to the CPU to 1 Mbps and ignores BGP traffic that is sent at higher rate?
- A. policy-map SHAPE_BGP
- B. policy-map LIMIT_BGP
- C. policy-map POLICE_BGP
- D. policy-map COPP
Answer: D
NEW QUESTION 18
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 19
An engineer is trying to copy an IOS file from one router to another router by using TFTP. Which two actions are needed to allow the file to copy? (Choose two.)
- A. Copy the file to the destination router with the copy tftp: flash: command
- B. Enable the TFTP server on the source router with the tftp-server flash: <filename> command
- C. TFTP is not supported in recent IOS versions, so an alternative method must be used
- D. Configure a user on the source router with the username tftp password tftp command
- E. Configure the TFTP authentication on the source router with the tftp-server authentication local command
Answer: AB
NEW QUESTION 20
Drag and drop the DHCP messages from the left onto the correct uses on the right.
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 21
Refer to the exhibit.
Which subnet is redistributed from EIGRP to OSPF routing protocols?
- A. 10.2.2.0/24
- B. 10.1.4.0/26
- C. 10.1.2.0/24
- D. 10.2.3.0/26
Answer: A
NEW QUESTION 22
R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:
What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?
- A. R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.
- B. R1 does not accept any routes other than 192.168.130.0/24
- C. R1 does not forward traffic that is destined for 192.168.30.0/24
- D. Network 192.168.130.0/24 is not allowed in the R1 table
Answer: A
NEW QUESTION 23
......
Recommend!! Get the Full 300-410 dumps in VCE and PDF From Simply pass, Welcome to Download: https://www.simply-pass.com/Cisco-exam/300-410-dumps.html (New 58 Q&As Version)