How Many Questions Of 300-625 Study Guide

NEW QUESTION 1
A storage administrator is enabling DH-CHAP for the first time on a Fibre Channel fabric. Which condition must the administrator consider while configuring this feature?

• A. NTP must be configured on all devices or the configuration fails.
• B. The MD5 hash must be used if TACACS+ or RADIUS authentication for FCSP is enabled.
• C. All switches on the fabric must be configured for the same password.
• D. Enabling DH-CHAP protocol feature is unsupported on FCIP interfaces.

Answer: B

NEW QUESTION 2
Refer to the exhibit.

Device alias information must be merged for two fabrics. Which setting must match on both fabrics before the merge can be performed successfully?

• A. device-alias mode
• B. session
• C. qos
• D. smart-zoning

Answer: A

NEW QUESTION 3
Refer to the exhibit.

What is the result of merging the fabric?

• A. The merged fabric IVR VSAN topology is set to activate.
• B. The merged fabric has NAT enabled.
• C. The merge is invalid.
• D. The merged fabric contains only service group Group1.

Answer: D

NEW QUESTION 4
Which two protocols are used to implement SAN telemetry on Cisco MDS switches? (Choose two.)

• A. RPC transport
• B. GPB transport
• C. gRPC transport
• D. gRPC encoding
• E. GPB encoding

Answer: CE

NEW QUESTION 5
A storage administrator is connecting two previously configured switches to make a single fabric. When the E Ports are connected, the administrator sees a ZONE MERGE FAILURE message referring to the zoneset for VSAN 10 on each switch. Which command should the administrator use to allow these switches to work together?

• A. zoneset import interface fc1/1 vsan 10
• B. zoneset distribute full vsan 10
• C. zoneset overwrite-control vsan 10
• D. zoneset copy active-zoneset full-zoneset

Answer: A

NEW QUESTION 6
An engineer is configuring a SAN environment and attempts to activate a zoneset, but a lock is held by another user. Which argument does the engineer use to clear the lock from the zoning database configuration?

• A. commit
• B. abort
• C. clear
• D. force

Answer: C

NEW QUESTION 7
What does an unlicensed DCNM SAN fail to display?

• A. Fibre Channel, FCoE, and iSCSI topologies
• B. events and fault management
• C. historical performance monitoring
• D. real-time performance monitoring

Answer: C

NEW QUESTION 8
Which result occurs when a VSAN is deleted that contains non-trunking ports?

• A. The ports are moved to VSAN 4094.
• B. The ports are moved to VSAN 1.
• C. The ports are removed from the configuration.
• D. The port configurations are cleared.

Answer: A

NEW QUESTION 9
DRAG DROP
Drag and drop the FLOGI parameters from the left onto the descriptions from which they were-derived on the right.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 10
Which configuration is needed to enable manual ESP mode for Fibre Channel TrustSec on Cisco MDS switches?

• A. MDS(config)# interface fc 1/1MDS(config-if)# fcsp esp manual
• B. MDS(config)# fcsp esp manual
• C. MDS(config)# interface fc 1/1 MDS(config-if)# fcsp mode gcm MDS(config-if-fcsp)# fcsp esp manual
• D. MDS(config)# interface fc 1/1 MDS(config-if)# fcsp esp manual MDS(config-if-fcsp)# mode gcm

Answer: A

NEW QUESTION 11
Which action must be performed to deactivate a VSAN without losing its configuration?

• A. Isolate it.
• B. Delete it.
• C. Rename it.
• D. Suspend it.

Answer: D

NEW QUESTION 12
Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?

• A. The autoreconfigure option is disabled on both switches.
• B. The autoreconfigure option is enabled on both switches.
• C. The rcf-reject option is enabled on the interfaces.
• D. The rcf-reject option is disabled on the interfaces.

Answer: A

NEW QUESTION 13
DRAG DROP
Drag and drop the mechanisms of Cisco Secure Boot from the left into the correct order on the right.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 14
DRAG DROP
Drag and drop the boot issues from the left onto the correct solutions on the right.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 15
Refer to the exhibits.


A storage network engineer activates a zoneset on MDS-A and verifies the successful activation (Exhibit 1). The engineer is then notified that there is a SAN outage (Exhibit 2) What is the cause of the outage?

• A. Another network engineer activated zoneset ZoneSetMDS-B-VSAN100 on MDS-A.
• B. Another network engineer issued the zone mode enhanced vsan 100 command on another switch in the fabric.
• C. Another network engineer activated the zoneset ZoneSetMDS-B-VSAN100 command on another switch in the fabric.
• D. Another network engineer issued the zone default-zone permit vsan 100 command on another switch in the fabric.

Answer: D

NEW QUESTION 16
Refer to the exhibit.

A port channel has been configured between a Cisco MDS and a Cisco Fabric Interconnect switch. Which interface(s) in the port channel carry the control plane traffic?

• A. per packet, balanced between interfaces fc1/9 and fc1/10
• B. from interface fc1/9
• C. from interface fc1/10
• D. per flow, balanced between interfaces fc1/9 and fc1/10

Answer: D

NEW QUESTION 17
Which command identifies the application and the user that have a Cisco Fabric Services session open?

• A. show cfs application
• B. show zoneset active
• C. show cfs lock
• D. show device-alias database

Answer: A

NEW QUESTION 18
Refer to the exhibit.

Which command is used to determine which switch has the lock?

• A. show zoneset active
• B. show zone status
• C. show flogi database

Answer: C

NEW QUESTION 19
Which condition requires using a device alias rather than a Fibre Channel alias?

• A. The zone database must be distributed over the fabric.
• B. The same alias must be used in zoning as well as DPVM.
• C. All aliases being used are being configured in the same VSAN.
• D. Aliases must be saved within a central database on the fabric.

Answer: A

NEW QUESTION 20
Which feature on MDS platforms ensures that the code that is running on the hardware platform is authentic and unmodified, while also validating the BIOS to eliminate any rootkits.

• A. Cisco Secure Boot
• B. UEFI Secure Boot
• C. Secure Unique Device Identifier
• D. BIOS Secure Boot

Answer: A

NEW QUESTION 21
After a subordinate switch requests a domain ID form a principal switch, the requested domain ID becomes the runtime domain ID, and all interfaces on the affected VSAN are isolated. What is a solution to the issue?

• A. Add the received ID to the allowed list.
• B. Configure a static domain on the subordinate switch and reboot the switch.
• C. Enable the FICON feature on the affected VSAN.
• D. Configure IVR NAT on the affected VSAN.

Answer: A

NEW QUESTION 22
A storage network engineer must configure a 48-port Cisco MDS switch to reject any login requests to VSAN 10 from unauthorized Fibre Channel devices and switches. All the devices that were already logged in to the switch from this VSAN must be allowed without any manual configuration. Which configuration must be applied?

• A. switch(config)# feature port-security switch(config)# port- security activate vsan 10
• B. switch(config)# feature port- security switch(config)# port-security activate vsan 10 no auto- learn
• C. switch(config)# feature port-security switch(config)# port-security database vsan 10 switch(config-port-security)# any-wwn interface fc1/1 – fc1/48
• D. switch(config)# port-security activate vsan 10

Answer: D

NEW QUESTION 23
Which two steps are mutual between Cisco secure boot and UEFI secure boot? (Choose two.)

• A. bootloader
• B. operating system
• C. microloader
• D. kemel
• E. hardware anchor

Answer: AB

NEW QUESTION 24
A storage network engineer is implementing disk-array data replication between two SAN environments in two different data centers not connected via Fibre Channel. Which SAN switch feature must be implemented?

• A. FCIP
• B. zoning merge over LAN
• C. VSAN scoping
• D. IVR

Answer: A

NEW QUESTION 25
A storage administrator is upgrading Cisco NX-OS on a Cisco MDS switch. The administrator performs an ISSU upgrade following the configuration guide. While the install is proceeding, the administrator connects a new server to the switch, which cannot access storage. The existing servers continue to operate properly through the switch. Why is the new server failing to connect?

• A. The fabric data plane resets as part of the upgrade process.
• B. The new server is unable to log in to the fabric to receive an FC-ID.
• C. The upgrade process disables any currently unused ports.
• D. The zoning database is locked during the upgrade process.

Answer: D

NEW QUESTION 26
......