Pass4sure has the Cisco Cisco exam questions which usually with accurate and verified answers. They are going to appear inside the real Cisco 352-001 exam. Therefore taking total advantage of the Cisco 352-001 practice questions and answers, you should be successful in first attempt. The Cisco 352-001 training training course is a wonderful instrument to prepare the 352-001 exam. All of us provide any limited moment for the free of charge downloadable Cisco 352-001 exam dumps after paying. There is certainly no time to get rid of! Our Cisco 352-001 exam items are marketed at a discounted cost. Look no further more. Stop in Pass4sure website and buy your Cisco Cisco exam dumps right today. You will end up being capable of producing great improvement through the review with the Cisco 352-001 exam.

2021 Mar 352-001 free exam

Q41. When network summaries are created for access networks in a network design, how does it change the behavior of the Shortest Path First (SPF) running in a backbone area? 

A. There would be fewer incremental SPFs. 

B. There would be fewer partial SPFs. 

C. There would be fewer full SPFs. 

D. There would be no change with the SPFs. 

Answer: B 


Q42. A company wants to connect two data center sites using a hub-and-spoke design with 2000 remote sites. One design consideration is the requirement to transfer MPLS packets over the public Internet. In addition, one router at each site should be used, and the MPLS packets must be encapsulated inside IP packets because the public Internet cannot transfer native MPLS packets. Which feature can be used to simplify the network design? 

A. GET VPN can be used to encrypt the MPLS packets with IPsec. 

B. DMVPN can be used to build up GRE tunnels dynamically with MPLS encapsulation inside. 

C. L2TPv3 can be used to encapsulate the MPLS packets. 

D. Site-to-site IPsec without GRE can be used to encapsulate the MPLS packets. 

E. PPPoE can be used to encapsulate the MPLS packets. 

Answer: B 


Q43. Your company plans to implement an Internet gateway router that is performing NAT. This same gateway will be terminating various IPsec tunnels to other remote sites. Which 

address type isappropriate for the ACL that will govern the sources of traffic entering the tunnel in the inside interface? 

A. inside local 

B. inside global 

C. outside local 

D. outside global 

Answer: B 


Q44. The Service Provider you work for wants to deploy CoS functionality on the P routers of the MPLS core, to provide a complete CoS solution to all customers that purchase services such as dedicated Internet access, MPLS Layer 3 VPN, and Layer 2 VPN (pseudowire). The design requirements are: 

. The network supports four service queues with equal treatment for delay, jitter, 

and packet loss. 

. Queues are numbered 0–3, where 0 is the default queue. 

. Three queues have one treatment, whereas the other queue has either one or two 

treatments. 

. The Service Provider manages control traffic, whereas the customers manage 

business critical and best effort. 

Which two statements could you recommend to allow for the appropriate level of bandwidth allocation? (Choose two.) 

A. Control plane 10%, Real Time 30%, Business Critical 40%, Best Effort 20% 

B. Control plane 80%. Real Time 10%, Business Critical 5%, Best Effort 5% 

C. Control plane 90%, Real Time 5%, Business Critical 5%, Best Effort 0% 

D. Control plane 20%, Real Time 40%, Business Critical 30%, Best Effort 10% 

Answer: AD 


Q45. You work as a network designer for a company that is replacing their Frame Relay WAN with an MPLS VPN service, where the PE-to-CE routing protocol is BGP. The company has 3000 routes in their distribution routers, and they would like to advertise their access routers through the MPLS network. Their service provider, however, only supports 1000 prefixes per VRF. Which two design solutions can be applied to ensure that your access routers will be able to reach all devices in your network? (Choose two.) 

A. Use prefix lists on your distribution routers to control which routes are sent to the MPLS network. 

B. On your distribution routers, configure null routes and aggregate routes for the prefixes in your network. 

C. Configure your distribution routers to send a default route to the MPLS network. 

D. Summarize the routes on the MPLS WAN interfaces of your distribution routers. 

Answer: BC 


Abreast of the times 352-001 study guide:

Q46. Company X will be integrating an IPv6 application into their network and wants to develop a test environment to evaluate application performance across the network. This application will require both unicast and multicast communications. The company can do this implementation only in certain areas of its existing IPv4-only network, but wants all areas to communicate with each other. When developing the design to provide connectivity between these testing locations, what tunneling technology would work in this scenario? 

A. ISATAP 

B. 6to4 

C. DMVPN 

D. 6vPE 

E. 6PE 

Answer: C 


Q47. Which three techniques can be used to improve fault isolation in an enterprise network design? (Choose three.) 

A. aggregate routing information on an OSPF ABR 

B. fully meshed distribution layer 

C. Equal-Cost Multipath routing 

D. EIGRP query boundaries 

E. multiple IS-IS flooding domains 

F. tuned Spanning Tree Protocol timers 

Answer: ADE 


Q48. A company plans to establish a new network using Cisco Catalyst switches for its multicast applications. What is the disadvantage when two multicast applications are using the multicast IP addresses 234.17.4.5 and 234.145.4.5 inside the same network? 

A. Multicast packets from both applications are flooded to all Layer 2 ports in a segment where a multicast receiver is located. 

B. Multicast packets from both applications are flooded to ports where one multicast receiver from one application is located. 

C. Only one multicast stream is received at the port where the receivers from both applications are located. 

D. Both multicast senders will always receive the multicast packets from the other multicast application. 

E. The routers doing PIM-SM cannot distinguish between the two multicast applications. 

Answer: B 


Q49. A company supports IPv4 and IPv6 addresses, and they need to be able to support flow-based translations for multiple IPv6 devices to a single IPv4 address. Which address family translation design solution should be recommended? 

A. stateful NAT-PT 

B. NAT-PT 

C. stateless NAT64 

D. stateful NAT64 

Answer: D 


Q50. Refer to the exhibit. 

Acme Corporation hired you as a network designer to upgrade their network so that it supports IPv4 and IPv6 multicast. Which two protocols are needed on the LAN switch? (Choose two.) 

A. PIM sparse mode 

B. IGMP snooping 

C. PIM snooping 

D. Source Specific Multicast 

E. MLD snooping 

Answer: BE