Your success in Cisco 400 101 ccie is our sole target and we develop all our 400 101 pdf braindumps in a way that facilitates the attainment of this target. Not only is our 400 101 pdf study material the best you can find, it is also the most detailed and the most updated. 400 101 pdf Practice Exams for Cisco CCIE Routing and Switching ccie 400 101 are written to the highest standards of technical accuracy.
P.S. High value 400-101 pdf are available on Google Drive, GET MORE: https://drive.google.com/open?id=1GGI_rFzsSx1M95iUGUrA8n3R9FtM_FJK
New Cisco 400-101 Exam Dumps Collection (Question 15 - Question 24)
Question No: 15
which three statements about the route preference of IS-IS are true?(choose two)
A. An L1 path is preferred over an L2 path
B. Within each level, a path that supports optional metric is preferred over a path that supports only the default metric
C. The Cisco IS-IS implementation usually performs equal cost path load balancing on up to eight paths.
D. An L2 path is preferred over an L1 path
E. Both L1 and L2 routes will be installed in the routing table at the same time
F. Within each level of metric support, the path with the lowest metric is preferred.
Answer: A,B,F
Question No: 16
when is it useful to disable split horizon on an EIGRP interface?
A. Disable it when you want to sent routes that are learned from another routing protocol to peer on the same interface
B. Disable it when you want to provide additional backup paths in your network
C. It is never advisable to disable split horizon on an EIGRP interface
D. Disable it when you need to send updates to peers on the interface on which the updates were received
Answer: D
Question No: 17
Which statement about NAT64 is true?
A. NAT64 should be considered as a permanent solution.
B. NAT64 requires the use of DNS64.
C. NAT64 provides address family translation and translates IPv4 to IPv6 and IPv6 to IPv4.
D. NAT64 provides address family translation and can translate only IPv6 to IPv4.
Answer: D
Question No: 18
If running an OSPF process without the capability vrf-lite command in a VRF, which value does the router
additionally check on an OSPF Type 3 LSA?
A. the tag
B. the Max Age timer
C. the prefix length
D. the DN bit
Answer: D
Question No: 19
which two conditions are required for tracking the interface IP routing state?(choose two)
A. The interface line protocol must be up
B. Cisco Express Forwarding must be disable on the interface
C. A VRF must be enabled on the interface
D. A known IP address must be configured on the interface
E. IP routing must be disabled on the interface
Answer: A,D
Question No: 20
Which two statements about AT0M are true? (Choose two)
A. When using AToM, the IP precedence field is not copied to the MPLS packet
B. It provides support for L2VPN features on ATM interfaces
C. It encapsulates Layer 2 frames at the egress PE
D. AToM supports connecting different L2 technologies using internetworking option
E. The loopback address of the PE router must be either /24 or /32
Answer: A,D
Question No: 21
What are the two BFD modes? "(Choose two)
A. active
B. asynchronous
C. passive
D. established
E. demand
F. synchronous
Answer: B,E
Question No: 22
Refer to the exhibit.
R2 is configured with an IP helpler address on Gi0/0/0 and it is sharing routes with R1 using OSPF. If PC1 is configured to request an IP address from the DHCP server, which two statements
correctly describe communications between the devices on the netwok?(choose two)
A. R1 forwards DHCPREQUEST messages to IP address 172.16.1.100
B. PC1 sends DHCPDISCOVER messages to IP address 255.255.255.255
C. R1 forwards DHCPDISCOVER messages to IP address 255.255.255.255
D. PC1 sends DHCPREQUEST messages to IPaddress 255.255.255.255
E. R1 forwards DHCPOFFER messages to IP address 172.16.1.100
Answer: A,B
Question No: 23
Refer to the exhibit.
If the given network is in the process of being migrated from EIGRP to OSPF , includes external routes, and all routers are currently running both protocol action must you perform
to complete the migration?
A. Change the EIGRP Administrative Distance to 111, wait until all routers are present, and then change it back to the default value.
B. Change the OSPF Administrative Distance to 91, wait until all routers are present, and then change it back to the default value.
C. Change the EIGRP Administrative Distance to match the OSPF Administrative Distance, wait until all
Routers are present, and then change the EIGRP Administrative Distance back to the default value.
D. Change the OSPF Administrative Distance to 171, wait until all routers are present, and then change it
back to the default value.
Answer: D
Question No: 24
which three session tables does NAT64 maintain?
A. UDP
B. TCP
C. 6rd
D. 464XLAT
E. ICMP Query
F. SIP
Answer: A,B,E
P.S. Easily pass 400-101 Exam with Surepassexam High value Dumps & pdf vce, Try Free: https://www.surepassexam.com/400-101-exam-dumps.html (911 New Questions)