Exambible 4A0-M01 Questions are updated and all 4A0-M01 answers are verified by experts. Once you have completely prepared with our 4A0-M01 exam prep kits you will be ready for the real 4A0-M01 exam without a problem. We have Most up-to-date Alcatel-Lucent 4A0-M01 dumps study guide. PASSED 4A0-M01 First attempt! Here What I Did.
Q25. Which statement describes an instance where a control word would be required in an aPipe service?
A. ATM cell mode is used to map multiple virtual circuits into a single aPipe service
B. The aPipe service transports concatenated cells from an entire virtual path
C. The service carries just the cell payload and Equal Cost Multipath (ECMP) is used in the transport
D. A cell mode service must map different ATM virtual circuits to a service based on Quality of Service (QoS) profiles
Answer: C
Q26. Which statement correctly describes eNodeB-to-eNodeB X2 interface traffic flow in the Model 1 hub and spoke architecture Long Term Evolution (LTE) service model shown?
A. X2 traffic travels through the red Virtual Private LAN Service (VPLS) tothe Mobility Management Entity (MME) pool and on to the target CSA router
B. The green Internet Enhanced Service (IES) provides the Layer 3 interfaces used for X2 eNodeB-to-eNodeB handoff traffic
C. Split horizon allows direct eNodeB-eNodeB handoff without the need to route through the green IES interfaces
D. The red VPLS supports Virtual Routing and Redundancy Protocol (VRRP) sessions for X2 inter-eNodeB Layer 3 interface resiliency
Answer: B
Q27. Given the show command results and the configuration shown:
Why did the head end router fail to protect the Label Switch Path (LSP) between
POC3-1 and POC3-2 with the configured manual bypass tunnel?
A. The protected LSP must specify manual bypass required
B. The bypass tunnel path must explicitly specify each hop to the tail end
C. The manual bypass LSP must terminate on the bypass path last hop entry
D. The protected LSP must specify fast reroute facility
Answer: D
Q28. Click on the exhibit.
Given the command example shown, and the following information:
* CSA1 originates a switched ePipe service
* Each spoke SDP transports traffic to an S-PE
* Each spoke SDP uses the default spoke precedence value Which would cause the error message shown when you try to create another spoke SDP binding?
A. A service can have a total of four endpoint objects across all endpoints
B. The spoke SDP cannot be added since it would preempt the active spoke SDP
C. The spoke binding must include the endpoint name as part of its configuration
D. The new spoke SDP Virtual Circuit (VC)-ID must match the service ID
Answer: A
Q29. Given the show result shown:
Which example shows the proper format for a Service Access Point (SAP) configured within this service context?
A. sapbundle-ppp-1/2.1:1/200
B. sap bundle-ima-2/1.1:1
C. sap 1/1/1.1:200.20
D. sap 1/1/6.1:200/20
Answer: D
Q30. Which statement describes a Management-Virtual Private LAN Service (mVPLS) characteristic?
A. The mVPLS Service Access Points (SAPs) are interconnected in a loop identical to the protected services
B. An mVPLS runs Rapid Spanning Tree Protocol (RSTP) to block individual physical access ports
C. The mVPLS runs Spanning Tree Protocol (STP) on behalf of the customer edge (CE) devices
D. The mVPLS SAP Virtual LAN (VLAN) tags must match those used in the protected service SAPs
Answer: A
Q31. Click on the exhibit Given the show command and the result shown: Which payload type does this service transport?
A. A channelized E1 circuit carrying all 32 timeslots
B. An unframedDSI circuit carrying all 24 timeslots
C. Multilink Protocol (MP) framed bundled E1s
D. Ethernet over TDM framed DS1 circuits
Answer: B
Q32. Given the configuration shown and the following information:
. The Virtual Private Routed Network (VPRN) service 2 interface "ipipe200" cross- connects the VPRN with the IP Interworking Pipe (iPipe) service 200 SAP 1/1/8:200.
. The iPipe spoke-SDP 1:200 transports traffic to and from the Cell Site Aggregator (CSA) router
. The CSA hosts the far-end iPipe service on which a Multilink Point-to-Point (MLPPP) CE device SAP is configured
What can you add to the VPRN 2 interface "ipipe200" configuration to ensure that the VPRN service always knows the correct destination Media Access Control (MAC) address for the far-end CE device with the IP address 192.51.100.26?
A. A static MAC address entry on the VPRN 2 interface "ipipe200" mapping the CE device MAC address to its assigned IP address
B. A static Address Resolution Protocol (ARP) entry to the iPipe 200 spoke-sdp 1:200 mapping the CE device MAC address to its assigned IP address
C. A static ARP entry on the iPipe 200 sap 1/1/8:200 mapping the CE device MAC address to its assigned IP address
D. A static ARP entry on the VPRN 2 interface "ipipe 200" mapping the CE device MAC address to its assigned IP address
Answer: D