Exam Code: CQE (Practice Exam Latest Test Questions VCE PDF)
Exam Name: Certified Quality Engineer Exam
Certification Provider: ASQ
Free Today! Guaranteed Training- Pass CQE Exam.
2021 Aug CQE exam cost
Q1. During the performance of an audit, which of the following are key considerations?
. What sampling plans may be necessary?
. Is the audit schedule progressing as planned?
. Is there a need for a technical specialist?
. Is the level of compliance satisfactory?
A. I,IIandIIIonly
B. IIandIVonly
C. I andIVonly
D. I,II,IIIandIV
Answer: B
Explanation:
Q2. A typical use for the optical comparator would be to measure
A. Surface finish.
B. Contours.
C. Depth of holes.
D. Diameters of internal grooves.
Answer: B
Explanation:
Q3. The MOST essential value of a surface plate in precision measurement application is which of the following?
A. It provides a flat working surface.
B. It provides a surface free of minor vibration.
C. It provides an accurate reference surface.
D. It provides a chemically resistant work surface.
Answer: C
Explanation:
Q4. What is the standard deviation of the values below?
4.5, 5.1, 6.2, 2.1, 3.9
A. 1.136
B. 2.087
C. 1.362
D. 1.522
Answer: C
Explanation:
Q5. Applications for surface plate includes which of the following?
. Referencing plane for length measurements.
. Referencing plane for parallelism measurements.
. Establishing a datum plane for dimensional layout.
. Waiting place for delicate parts.
. Keeping extra gages when not in use.
A. I andIIonly
B. I andIVonly
C. I,IIandIIIonly
D. IIIand V only
Answer: C
Explanation:
Updated CQE book:
Q6. Two advantages of process mapping are the ability to
. Visualize the process being described.
. Discover manufacturing problems only.
. Discover quality problems only.
IV.
Check current processes for duplication or redundancy.
A.
I andIVonly
B.
IIandIIIonly
C.
I andIIIonly
D.
IIandIVonly
Answer: A
Explanation:
Q7. Which of the following is the BEST statement to make regarding the relationship between product precision and product production?
A. With too little precision, production costs increase.
B. With too much precision, production costs increase.
C. Precision costs and performance are related.
D. With little precision, performance will improve.
Answer: C
Explanation:
Q8. The use of 100% inspection normally means
A. That the final customers will not experience defective product.
B. That selected characteristics have been evaluated against specified standards.
C. That there will be an opportunity to rework any product deemed to be outside of specifications.
D. That the lowest over-all quality costs have been considered.
Answer: B
Explanation:
Q9. Which of the following statements describes discrete data?
A. It takes 3 hours 48 minutes to fly from LA to New York.
B. Of 225 people on the airplane, 85 had connecting flights.
C. The flight arrived at 9:08 PM.
D. There were 5,923 gallons of fuel consumed on the flight.
Answer: B
Explanation:
Q10. An X-bar and R chart with n=5 has been plotted for some time and has demonstrated random variation. Upon review of the last 30 plot points, the expected number of runs around the centerline on the X-bar chart is expected to be approximately which of the following?
A. 4
B. 9
C. 12
D. 16
Answer: D
Explanation:
106. What is the lower control limit for proportion defective if the average daily production is 5000 units and the average fraction defective is 0.02?
A. 0.016
B. 0.014
C. 0
D. 0.010
Answer: B
Explanation: