Your success in Network Appliance NS0-156 is our sole target and we develop all our NS0-156 braindumps in a way that facilitates the attainment of this target. Not only is our NS0-156 study material the best you can find, it is also the most detailed and the most updated. NS0-156 Practice Exams for Network Appliance NS0-156 are written to the highest standards of technical accuracy.
Q73. - (Topic 1)
Which are predefined roles for cluster administrators in clustered ONTAP 8.2? (choose all that apply)
A. admin
B. read only
C. vsadmin
D. vsadmin-backup
E. vsadmin-readonly
F. backup
G. vsadmin-autosupport
H. none
Answer: A,B,H
Q74. - (Topic 3)
A FAS6280 running ONTAP 8.0.2 HAS A 32-bit root aggregate. After upgrading to Data ONTAP 8.1, what is the status of the root aggregate?
A. The root aggregate remains 32-bit
B. The root aggregate converts from 32 to 64-bit in place
C. The root aggregate auto-migrates to a new 64-bit aggregate
D. The upgrade fails with a message to create a new 64-bit aggregate before upgrade
Answer: A
Q75. - (Topic 1)
The fcadmin config command…
A. Is a Clustershell command
B. Is a Nodeshell command
C. Is a Systemshell command
D. Must be run in the advanced mode
Answer: B
Q76. - (Topic 1)
When storage failover (SFO) occurs and cluster mode SAN protocols are enabled on a data vserver:
A. ALUA determines that the HA partner is an active direct path
B. ALUA determines that the HA partner is an active indirect path
C. ALUA determines the best path for active optimize LUN access even if it requires use of the cluster interconnect
D. ALUA does not factor into the path selection during Storage Failover (SFO)
Answer: A
Q77. - (Topic 2)
Which statement is true about a SnapMirror destination vserver?
A. It must have a read-only Vserver root volume.
B. It must be in the same cluster as the source Vserver
C. It must be created with the same language type as the source Vserver.
D. It must have a different storage efficiency policy than the source Vserver.
Answer: C
Explanation:
Training material: Clustered_Data_ONTAP_82_Data_Protection_Guide How volume SnapMirror works with deduplication You can use volume SnapMirror to replicate a deduplicated volume regardless of size of the volume and logical data in the volume. When using volume SnapMirror with deduplication, you must consider the following information: You can enable deduplication on the source system, the destination system, or both systems. The shared blocks are transferred only once. Therefore, deduplication also reduces the use of network bandwidth. When the volume SnapMirror relationship is broken, the default deduplication schedule is applied at the destination storage system. When configuring volume SnapMirror and deduplication, you should coordinate the deduplication scheduleand the volume SnapMirror schedule. You should start volume SnapMirror transfers of a deduplicated volume after the deduplication operation is complete. This schedule prevents the sending of undeduplicated data and additional temporary metadata files over the network. If the temporary metadata files in the source volume are locked in Snapshot copies, these files consume extra space in the source and destination volumes.
Q78. - (Topic 2)
What two actions should an administrator take before shutting down two nodes of a 4-node cluster? (Choose two.)
A. reassign the master of all RDB rings to a node that will be staying up
B. migrate node-management LIFs to a node that will be staying up
C. move Vserver root volumes to a node that will be staying up
D. set both nodes that are coming down to “ineligible”
E. ensure that Epsilon is assigned to one of the nodes that will be staying up
Answer: D,E
Q79. - (Topic 3)
What is the GUI-based interface that manages a cluster?
A. Cluster Bench
B. Device Manager
C. FilerView
D. Node Studio
E. System Manager
Answer: E
Explanation:
http://www.netapp.com/us/products/management-software/system-manager.aspx
Q80. - (Topic 2)
What is the file extension for NDMP backup CAB (Cluster Aware Backup extension)
A. CAB
B. BAC
C. CAP
D. NDBC
Answer: A