Examcollection offers free demo for NS0-180 exam. "NetApp Certified Storage Installation Engineer, Clustered Data ONTAP", also known as NS0-180 exam, is a Network Appliance Certification. This set of posts, Passing the Network Appliance NS0-180 exam, will help you answer those questions. The NS0-180 Questions & Answers covers all the knowledge points of the real exam. 100% real Network Appliance NS0-180 exams and revised by experts!
Q25. A customer wants you to add a disk shelf that contains SSDs so they can implement Flash Pool.
Which three tools would you use to complete this task? (Choose three.)
A. Use the My AutoSupport tool to ensure that Flash pool is licensed.
B. Use Hardware Universe to ensure that you would not exceed the maximum drive count.
C. Use Hardware Universe to ensure that you would not exceed the maximum cache for the system.
D. Use the My AutoSupport tool to see if there is a Flash Cache card installed.
E. Use Config Builder to verify the shelves can be added.
Answer: A,B,E
Explanation:
The Hardware Universe (HWU) application is NetApp's system configuration solution, replacing the System Configuration Guides.
Q26. You want to install a new clustered Data ONTAP 8.3 system. The customer wants to use open ports on interconnect switches from a different system with clustered Data ONTAP
8.2 because they are running out of space in their rack.
What should be considered in this scenario?
A. Only one cluster per switch pair is qualified and supported.
B. You can use all free network ports for the cluster interconnect.
C. You can only use dedicated ports for the clustered interconnect.
D. A maximum of two clusters per switch pair are qualified and supported, but you should use trunked ports.
Answer: C
Q27. Multiple customers want to access a cluster from different domains that may contain duplicate IP addresses.
In this situation, which feature should you use?
A. IPspaces
B. interface groups
C. VLAN
D. logical interfaces
Answer: A
Explanation:
IPspaces enable you to configure a single Data ONTAP cluster so that it can be accessed by clients from more than one administratively separate network domain, even if those clients are using the same IP address subnet range Reference: Clustered Data ONTAP 8.3, Network Management Guide, page 32
Q28. Click the Exhibit button.
You are asked to install a 6-node cluster running clustered Data ONTAP 8.3 using Cisco switches. The customer has installed Config Advisor on a PC on their network and has asked you to help them collect data.
Referring to the exhibit, which three parameters should be selected? (Choose three.)
A. Enable management switch connections
B. Switchless
C. Enable cluster switch connections
D. Cisco NX5010/NX5020/5596/5596T
E. NetApp CN1610/CN1601
Answer: A,D,E
Explanation:
In the clustered Data ONTAP profile, you can choose any one of the following (based on
the network switch used):
Cisco NX5010/5020/5596 (Cisco switches is used in this question)
NetApp CN1610/CN1601 To verify clustered configurations, you should ensure the
following:
The data is collected from cluster switches, management switches, and a controller. Etc.
Netapp NS0-180 : Practice Test
Reference:
Config Advisor 3.2. Installation and Administration Guide, page 21
Q29. You have completed the installation of a 4-node cluster. The customer did not purchase management switches and will not allow your laptop on the network.
In this situation, what are two valid procedures that will allow you to collect the Config Advisor output? (Choose two.)
A. Bring a switch that allows you to connect your laptop to all the switches and controllers.
B. Connect to a single controller in the cluster since it can run commands on every node.
C. Ask the customer to install and run Config Advisor on one of their PCs on the network.
D. Connect four USB serial cables to your laptop to allow you to connect to all four controllers.
Answer: B,C
Q30. A remote administrator is connecting to a cluster from a different remote network.
According to NetApp best practices, which type of LIF routing is required to accomplish this task?
A. cluster LIF
B. data LIF
C. cluster management LIF
D. intercluster LIF
Answer: B
Explanation:
Data ONTAP services may initiate network connections from a node in the cluster. For example: AutoSupport, SNMP, time synchronization, and syslog. When a Node Management interface is configured and available, it is preferred for these connections. When Data ONTAP contacts name services like Active Directory, NIS, DNS, or LDAP, it prefers to initiate these connections from Data or SVM Management interfaces belonging to the Storage Virtual Machine (SVM). Note: A LIF role determines the kind of traffic that is supported over the LIF, along with the failover rules that apply and the firewall restrictions that are in place. The five LIF roles are: Cluster-management LIF Node-management LIF Cluster LIF Data LIF Intercluster LIF
Reference: What LIF roles does clustered Data ONTAP use to establish connections to remote servers?
https://kb.netapp.com/support/index?page=content&id=3012724&locale=en_US
Q31. You are asked to install a cluster that consists of two FAS8060 controllers and four DS2246 shelves. The customer wants two stacks of shelves (10-11 and 20-21).
According to NetApp, how many SAS cables are required to complete this installation with MPHA?
A. 10 SAS cables
B. 12 SAS cables
C. 8 SAS cables
D. 6 SAS cables
Answer: B
Explanation:
Example (with two controllers and six shelves which uses 12 SAS cables): Multipath HA configuration:
Reference: SAS Disk Shelves, Universal SAS and ACP Cabling Guide, page 10 https://library.netapp.com/ecm/ecm_get_file/ECMM1280392
Q32. What is NetApp's best practice regarding Ethernet flow control?
A. Leave flow control enabled.
B. Disable flow control on the switch ports.
C. Disable flow control on the host, switch, and all node ports.
D. Disable flow control on all 10Gbps ports.
Answer: D
Explanation:
The NetApp Best Practice specifies that Flow Control settings for 10G cluster ports are to
be set with Flow Control = None.
Reference:
How to modify the Flow Control setting on clustered Data ONTAP cluster ports
https://kb.netapp.com/support/index?page=content&id=1015245&actp=LIST_RECENT