Your success in Tibco Software Inc TB0-111 is our sole target and we develop all our TB0-111 braindumps in a way that facilitates the attainment of this target. Not only is our TB0-111 study material the best you can find, it is also the most detailed and the most updated. TB0-111 Practice Exams for Tibco Software Inc TB0-111 are written to the highest standards of technical accuracy.

Q25. You want to configure Rendezvous routing daemons (RVRDs) to bridge messages between Subnet A and B in such a way that only the required subjects cross the subnet boundaries. This prevents unnecessary message traffic flow across subnets. What is the documented best practice to accomplish this? 

A. The sending transport should set the flag in the messages that are allowed to cross the subnet boundaries, thus allowing RVRD to forward messages to neighboring subnets. 

B. The RVRD subject export/import wildcard subject ">" is used to allow RV protocol messages to be forwarded from Subnet A to Subnet B in order for RV protocols to work as intended. 

C. The subject export/import configuration is left blank so RVRD will decide by itself based on subscription interests how the subjects will forward the required messages in the most efficient way. 

D. For RVRD subject export/import, more specific subject names are used (such as FOO.>, NAME.>) to prevent some RV protocol messages from being unnecessarily forwarded from one subnet to another. 

Answer: D 


Q26. A Rendezvous fault-tolerant group (RVFT) has an active goal of 1. Member A with a weight of 100 is active and Member B with a weight of 200 joins the fault-tolerant group. Which statement describes the RVFT protocol behavior under normal operating conditions? 

A. Member A will deactivate and Member B will activate. 

B. Member B will remain inactive until Member A terminates. 

C. Member A will remain active and adjust its weight to be higher than the new Member B. 

D. Member B will activate and a TOO_MANY_ACTIVE advisory will be broadcast to the group. 

Answer: A 


Q27. For Rendezvous secure daemon (RVSD), subject access can be restricted to specific users. Where on the RVSD browser interface is this feature configured? 

A. on the User's page 

B. on the Subject Access page 

C. on the Limiting Access page 

D. on the Authorize Subjects page 

Answer: C 


Q28. Given the following RVTRACE capture: 

Which two statements are correct? (Choose two.) 

A. UDP service 5090 has the least amount of traffic. 

B. 10.101.3.67 is sending packets on UDP service 7500 and 5090. 

C. Retransmitted data are not within the allowable documented limits. 

D. The network has Rendezvous transports using multicast and broadcast addressing. 

Answer: C,D 


Q29. Which two statements are correct about virtual communication (VC)? (Choose two.) 

A. The terminal can reconnect after a failure. 

B. Messages arrive in the same order as the opposite terminal that sent them. 

C. A failure anywhere along the circuit causes the entire circuit to stop functioning. 

D. All transports listening on the same service as the VC transport, receive all messages. 

Answer: B,C 


Q30. When an event occurs, the places the event object on the , where it awaits dispatch to its callback function. 

A. rv daemon; rv queue 

B. event driver;rv quseue 

C. rv daemon; event queue 

D. event driver; event queue 

Answer: D 


Q31. Rendezvous daemon (RVD) is installed on Host A, but not on Host B. On Host A, you start a tibrvlisten using command tibrvlisten -service 8500 "FOO.>" and it spawns an RVD. Which two tibrvsend commands that run on Host B will successfully make it to tibrvlisten on Host A? (Choose two.) 

A. tibrvsend -daemon 7500 -service 8500 FOO.bar HELLO B. 

tibrvsend -daemon 7500 -service 8500 FOO.FOO HELLO C. tibrvsend -listen tcp:Host 

D. 7500 -service 8500 FOO.BAR HELLO 

D. tibrvsend -daemon tcp:Host 

E. 7500 -service 8500 FOO.bar HELLO 

E. tibrvsend -daemon tcp:Host 

F. 7500 -service 8500 FOO.BAR HELLO 

F. tibrvsend -daemon tcp:Host 

G. 7500 -service 8500 FOO.FOO HELLO 

Answer: A,B 


Q32. Which two statements are correct about the Rendezvous routing daemons (RVRDs)? (Choose two.) 

A. An RVRD can serve only one local network. 

B. An RVRD can serve multiple local networks. 

C. An RVRD can connect to multiple neighbors. 

D. An RVRD can have only one router configured. 

E. Two RVRD daemons can have the same router name. 

Answer: B,C