Master the icnd2 200 105 Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) content and be ready for exam day success quickly with this Testking ccna routing and switching icnd2 200 105 official cert guide dumps. We guarantee it!We make it a reality and give you real cisco 200 105 questions in our Cisco cisco 200 105 braindumps.Latest 100% VALID Cisco 105 200 Exam Questions Dumps at below page. You can use our Cisco ccna routing and switching icnd2 200 105 official cert guide braindumps and pass your exam.
Q41. - (Topic 2)
Refer to the exhibit.
What information about the interfaces on the Main_Campus router is true?
A. The LAN interfaces are configured on different subnets.
B. Interface FastEthernet 0/0 is configured as a trunk.
C. The Layer 2 protocol of interface Serial 0/1 is NOT operational.
D. The router is a modular router with five FastEthernet interfaces.
E. Interface FastEthernet 0/0 is administratively deactivated.
Answer: B
Explanation:
Interface fa0/0 breaks into sub-interfaces and Main_Campus router is connected with switch via fa0/0 .Subinterfaces configured with different subnet masks so the same switch has multiple vlans and allows communication between these VLAN's. For routing and inter-vlan we need to configure a trunk port. So B will be the correct answer.
Q42. - (Topic 3)
Refer to the exhibit.
Which WAN protocol is being used?
A. ATM
B. HDLC
C. Frame Relay
D. PPP
Answer: C
Explanation:
"Show interface pos8/0/0" command showing LMI enq sent which show frame-relay encapsulation enabled on this interface. Cisco supports three different Local Management Interface (LMI) types for Frame Relay: Cisco, ANSI Annex D, and Q933-A Annex A http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=3
Q43. - (Topic 3)
Refer to the exhibit.
A technician pastes the configurations in the exhibit into the two new routers shown. Otherwise, the routers are configured with their default configurations. A ping from Host1 to Host2 fails, but the technician is able to ping the S0/0 interface of R2 from Host1. The configurations of the hosts have been verified as correct. What is the cause of the problem?
A. The serial cable on R1 needs to be replaced.
B. The interfaces on R2 are not configured properly.
C. R1 has no route to the 192.168.1.128 network.
D. The IP addressing scheme has overlapping subnetworks.
E. The ip subnet-zero command must be configured on both routers.
Answer: C
Explanation:
Whenever a node needs to send data to another node on a network, it must first know where to send it. If the node cannot directly connect to the destination node, it has to send it via other nodes along a proper route to the destination node. A remote network is a network that can only be reached by sending the packet to another router. Remote networks are added to the routing table using either a dynamic routing protocol or by configuring static routes. Static routes are routes to networks that a network administrator manually configured.So R should have static route for the 192.168.1.128.
Q44. - (Topic 3)
Which command is used to enable CHAP authentication, with PAP as the fallback method, on a serial interface?
A. Router(config-if)# ppp authentication chap fallback ppp
B. Router(config-if)# ppp authentication chap pap
C. Router(config-if)# authentication ppp chap fallback ppp
D. Router(config-if)# authentication ppp chap pap
Answer: B
Explanation:
The command “ppp authentication chap pap” command indicates the CHAP authentication is used first. If it fails or is rejected by other side then uses PAP instead. If you want to use PAP first (then CHAP) you can use the “ppp authentication pap chap” command
Reference: http://www.cisco.com/en/US/docs/ios/12_2/security/configuration/guide/scfathen.html
Q45. - (Topic 2)
Which statement describes the process ID that is used to run OSPF on a router?
A. It is globally significant and is used to represent the AS number.
B. It is locally significant and is used to identify an instance of the OSPF database.
C. It is globally significant and is used to identify OSPF stub areas.
D. It is locally significant and must be the same throughout an area.
Answer: B
Explanation: The Process ID for OSPF on a router is only locally significant and you can use the same number on each router, or each router can have a different number-it just doesn't matter. The numbers you can use are from 1 to 65,535. Don't get this confused with area numbers, which can be from 0 to 4.2 billion.
Q46. - (Topic 3)
Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?
A. IETF
B. ANSI Annex D
C. Q9333-A Annex A
D. HDLC
Answer: A
Explanation: Cisco supports two Frame Relay encapsulation types: the Cisco encapsulation and the IETF Frame Relay encapsulation, which is in conformance with RFC 1490 and RFC 2427. The former is often used to connect two Cisco routers while the latter is used to connect a Cisco router to a non-Cisco router. You can test with your Cisco router when typing the command Router(config-if)#encapsulation frame-relay ? on a WAN link. Note: Three LMI options are supported by Cisco routers are ansi, Cisco, and Q933a. They represent the ANSI Annex D, Cisco, and ITU Q933-A (Annex A) LMI types, respectively. HDLC is a WAN protocol same as Frame-Relay and PPP so it is not a Frame Relay encapsulation type.
Q47. - (Topic 3)
What occurs on a Frame Relay network when the CIR is exceeded?
A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.
Answer: D
Explanation:
Committed information rate (CIR): The minimum guaranteed data transfer rate agreed to by the Frame Relay switch. Frames that are sent in excess of the CIR are marked as discard eligible (DE) which means they can be dropped if the congestion occurs within the Frame Relay network. Note: In the Frame Relay frame format, there is a bit called Discard eligible (DE) bit that is used to identify frames that are first to be dropped when the CIR is exceeded.
Q48. - (Topic 2)
Refer to the exhibit.
A packet with a source IP address of 192.168.2.4 and a destination IP address of 10.1.1.4 arrives at the AcmeB router. What action does the router take?
A. forwards the received packet out the Serial0/0 interface
B. forwards a packet containing an EIGRP advertisement out the Serial0/1 interface
C. forwards a packet containing an ICMP message out the FastEthemet0/0 interface
D. forwards a packet containing an ARP request out the FastEthemet0/1 interface
Answer: C Explanation:
CCNA - EIGRP Common Question http://www.orbitco-ccna-pastquestions.com/CCNA---EIGRP-Common-Question.php
Looking at the output above, there is no IP route for 10.1.1.4 address on AcmeB routing table. If the router can no find a specific path in its routing table to a particular route,( In this case no path is found so AcmeB) the router will inform the source host with an ICMP message that the destination is unreachable and this will be through the same interface it has received the packet (interface Fa0/0 network 192.168.3.0/28 from the exhibit).
Topic 3, WAN Technologies
Q49. - (Topic 2)
What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?
A. 2
B. 4
C. 16
D. unlimited
Answer: B
Explanation:
4 is the default number of routes that OSPF will include in routing table if more than 4 equal cost routes exist for the same subnet. However, OSPF can include up to 16 equal cost routes in the routing table and perform load balancing amongst them. In order to configure this feature, you need to use the OSPF subcommand maximum-paths, i.e. maximum-paths 16.
Q50. - (Topic 2)
What is the default administrative distance of OSPF?
A. 90
B. 100
C. 110
D. 120
Answer: C
Explanation:
Default Distance Value Table This table lists the administrative distance default values of the protocols that Cisco supports: