Exam Code: 200-125 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: CCNA Cisco Certified Network Associate CCNA (v3.0)
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass 200-125 Exam.

Q1.  - (Topic 8)

How can you disable DTP on a switch port?

A. Configure the switch port as a trunk.

B. Add an interface on the switch to a channel group.

C. Change the operational mode to static access.

D. Change the administrative mode to access.

Answer: A


Q2.  - (Topic 8)

While troubleshooting a connection problem on a computer, you determined that the computer can ping a specific web server but it cannot connect to TCP port 80 on that server. Which reason for the problem is most likely true?

A. A VLAN number is incorrect.

B. A Route is missing

C. An ARP table entry is missing.

D. An ACL is blocking the TCP port.

Answer: D


Q3.  - (Topic 5)

Syslog was configured with a level 3 trap. Which 3 types of logs would be generated (choose four)

A. Emergencies

B. Alerts

C. Critical

D. Errors

E. Warnings

Answer: A,B,C,D

Explanation:

The Message Logging is divided into 8 levels as listed below: Level Keyword Description

0 emergencies System is unusable 1 alerts Immediate action is needed 2 critical Critical conditions exist

3 errors Error conditions exist

4 warnings Warning conditions exist

5 notification Normal, but significant, conditions exist 6 informational Informational messages

7 debugging Debugging messages

The highest level is level 0 (emergencies). The lowest level is level 7. If you specify a level with the “logging console level” command, that level and all the higher levels will be

displayed. For example, by using the “logging console warnings” command, all the logging of emergencies, alerts, critical, errors, warnings will be displayed.


Q4.  - (Topic 7)

Refer to the exhibit.

A problem with network connectivity has been observed. It is suspected that the cable connected to switch port Fa0/9 on Switch1 is disconnected. What would be an effect of this cable being disconnected?

A. Host B would not be able to access the server in VLAN9 until the cable is reconnected.

B. Communication between VLAN3 and the other VLANs would be disabled.

C. The transfer of files from Host B to the server in VLAN9 would be significantly slower.

D. For less than a minute, Host B would not be able to access the server in VLAN9. Then normal network function would resume.

Answer: D

Explanation:

Spanning-Tree Protocol (STP) is a Layer 2 protocol that utilizes a special-purpose algorithm to discover physical loops in a network and effect a logical loop-free topology. STP creates a loop-free tree structure consisting of leaves and branches that span the entire Layer 2 network. The actual mechanics of how bridges communicate and how the STP algorithm works will be discussed at length in the following topics. Note that the terms bridge and switch are used interchangeably when discussing STP. In addition, unless otherwise indicated, connections between switches are assumed to be trunks.


Q5.  - (Topic 5)

Which IPv6 address is valid?

A. 2001:0db8:0000:130F:0000:0000:08GC:140B

B. 2001:0db8:0:130H::87C:140B 

C. 2031::130F::9C0:876A:130B 

D. 2031:0:130F::9C0:876A:130B

Answer: D

Explanation:

An IPv6 address is represented as eight groups of four hexadecimal digits, each group

representing 16 bits (two octets). The groups are separated by colons (:). An example of an IPv6 address is 2001:0db8:85a3:0000:0000:8a2e:0370:7334. The leading 0’s in a group can be collapsed using ::, but this can only be done once in an IP address.

Topic 6, Infrastructure Security

261.  - (Topic 6)

Which set of commands is recommended to prevent the use of a hub in the access layer?

A. switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1

B. switch(config-if)#switchport mode trunk

switch(config-if)#switchport port-security mac-address 1

C. switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1

D. switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1

Answer: C

Explanation:

This question is to examine the layer 2 security configuration.

In order to satisfy the requirements of this question, you should perform the following configurations in the interface mode:

First, configure the interface mode as the access mode

Second, enable the port security and set the maximum number of connections to 1.


Q6.  - (Topic 5)

Refer to the exhibit.

Which address range efficiently summarizes the routing table of the addresses for router Main?

A. 172.16.0.0./21

B. 172.16.0.0./20

C. 172.16.0.0./16

D. 172.16.0.0/18

Answer: B

Explanation:

The 172.16.0.0./20 network is the best option as it includes all networks from 172.16.0.0 –

172.16.16.0 and does it more efficiently than the /16 and /18 subnets. The /21 subnet will not include all the other subnets in this one single summarized address.


Q7.  - (Topic 8)

Which configuration command can you apply to a router so that its local interface becomes active if all other routers in the group fail?

A. Router(config)#standby 1 preempt

B. No additional configuration is required

C. Router(config)#standby 1 Priority 250

D. Router(config)#standby 1 track Ethernet

Answer: A


Q8.  - (Topic 8)

A router has learned three possible routes that could be used to reach a destination network One route is from EIGRP and has a composite metric of 07104371. Another route is from OSPF with a metric of 782 The last is from RIPv2 and has a metric of 4 Which route or routes will the router install in the routing table?

A. the EIGRP route

B. the OSPF route

C. the RIPv2 route

D. all three routes

E. the OSPF and RIPv2 routes

Answer: A


Q9.  - (Topic 7)

Refer to the exhibit.

A network administrator attempts to ping Host2 from Host1 and receives the results that are shown. What is the problem?

A. The link between Host1 and Switch1 is down.

B. TCP/IP is not functioning on Host1

C. The link between Router1 and Router2 is down.

D. The default gateway on Host1 is incorrect.

E. Interface Fa0/0 on Router1 is shutdown.

F. The link between Switch1 and Router1 is down.

Answer: C

Explanation:

Host1 tries to communicate with Host2. The message destination host unreachable from Router1 indicates that the problem occurs when the data is forwarded from Host1 to Host2. According to the topology, we can infer that the link between Router1 and Router2 is down.


Q10.  - (Topic 7)

Which protocol can cause overload on a CPU of a managed device?

A. Netflow

B. WCCP

C. IP SLA

D. SNMP

Answer: D

Explanation:

Sometimes, messages like this might appear in the router console:

%SNMP-3-CPUHOG: Processing [chars] of [chars]

They mean that the SNMP agent on the device has taken too much time to process a request.

You can determine the cause of high CPU use in a router by using the output of the show process cpu command.

Note: A managed device is a part of the network that requires some form of monitoring and

management (routers, switches, servers, workstations, printers…).