It is impossible to pass Cisco 200 125 ccna exam without any help in the short term. Come to Pass4sure soon and find the most advanced, correct and guaranteed Cisco cisco 200 125 practice questions. You will get a surprising result by our Avant-garde CCNA Cisco Certified Network Associate CCNA (v3.0) practice guides.
Q31. - (Topic 8)
Which two statements about the tunnel mode ipv6ip command are true? (Choose two.)
A. It enables the transmission of IPv6 packets within the configured tunnel.
B. It specifies IPv4 as the encapsulation protocol.
C. It specifies IPv6 as the encapsulation protocol.
D. It specifies IPv6 as the transport protocol.
E. It specifies that the tunnel is a Teredo tunnel.
Answer: A,B
Q32. - (Topic 7)
Which router IOS commands can be used to troubleshoot LAN connectivity problems? (Choose three.)
A. ping
B. tracert
C. ipconfig
D. show ip route
E. winipcfg
F. show interfaces
Answer: A,D,F
Explanation:
Ping, show ip route, and show interfaces are all valid troubleshooting IOS commands. Tracert, ipconfig, and winipcfg are PC commands, not IOS.
Q33. - (Topic 5)
What are the alert messages generated by SNMP agents called?
A. TRAP
B. INFORM
C. GET
D. SET
Answer: A,B
Explanation:
A TRAP is a SNMP message sent from one application to another (which is typically on a remote host). Their purpose is merely to notify the other application that something has happened, has been noticed, etc. The big problem with TRAPs is that they’re
unacknowledged so you don’t actually know if the remote application received your oh-so- important message to it. SNMPv2 PDUs fixed this by introducing the notion of an INFORM, which is nothing more than an acknowledged TRAP.
Q34. - (Topic 3)
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)
A. Router(config)# router ospf 0
B. Router(config)# router ospf 1
C. Router(config)# router ospf area 0
D. Router(config-router)# network 192.168.16.0 0.0.0.255 0
E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0
F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0
Answer: B,E
Explanation:
In the router ospf command, the ranges from 1 to 65535 so o is an invalid number -> but To configure OSPF, we need a wildcard in the “network” statement, not a subnet mask. We also need to assgin an area to this process ->.
Q35. - (Topic 5)
In a GLBP network, who is responsible for the ARP request?
A. AVF
B. AVG
C. Active Router
D. Standby Router
Answer: B
Explanation:
Members of a GLBP group elect one gateway to be the active virtual gateway (AVG) for that group. Other group members provide backup for the AVG in the event that the AVG becomes unavailable. The AVG assigns a virtual MAC address to each member of the GLBP group. Each gateway assumes responsibility for forwarding packets sent to the virtual MAC address assigned to it by the AVG. These gateways are known as active virtual forwarders (AVFs) for their virtual MAC address.
The AVG is responsible for answering Address Resolution Protocol (ARP) requests for the virtual IP address. Load sharing is achieved by the AVG replying to the ARP requests with different virtual MAC addresses.
Reference: http://www.cisco.com/en/US/docs/ios/12_2t/12_2t15/feature/guide/ft_glbp.html
Q36. - (Topic 7)
Refer to the exhibit.
If the devices produced the given output, what is the cause of the EtherChannel problem?
A. SW1's Fa0/1 interface is administratively shut down.
B. There is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
C. There is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
D. There is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
Answer: D
Explanation:
You must configure all interfaces in an EtherChannel to operate at the same speeds and duplex modes. Based on the output shown, SW1 is configured to run at 10Mb while SW2 is operating at 100 Mb.
Q37. DRAG DROP - (Topic 6)
Drag the security features on the left to the specific security risks they help protect against on the right. (Not all options are used.)
Answer:
Q38. - (Topic 6)
A network administrator needs to configure port security on a switch. Which two statements are true? (Choose two.)
A. The network administrator can apply port security to dynamic access ports.
B. The network administrator can apply port security to EtherChannels.
C. When dynamic MAC address learning is enabled on an interface, the switch can learn new addresses, up to the maximum defined.
D. The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.
E. The network administrator can configure static secure or sticky secure MAC addresses in the voice VLAN.
Answer: C,D
Explanation:
Follow these guidelines when configuring port security:
+ Port security can only be configured on static access ports, trunk ports, or 802.1Q tunnel ports.
+ A secure port cannot be a dynamic access port.
+ A secure port cannot be a destination port for Switched Port Analyzer (SPAN).
+ A secure port cannot belong to a Fast EtherChannel or Gigabit EtherChannel port group.
+ You cannot configure static secure or sticky secure MAC addresses on a voice VLAN.
+ When you enable port security on an interface that is also configured with a voice VLAN, you must set the maximum allowed secure addresses on the port to at least two.
+ If any type of port security is enabled on the access VLAN, dynamic port security is automatically enabled on the voice VLAN.
+ When a voice VLAN is configured on a secure port that is also configured as a sticky secure port, all addresses seen on the voice VLAN are learned as dynamic secure addresses, and all addresses seen on the access VLAN (to which the port belongs) are learned as sticky secure addresses.
+ The switch does not support port security aging of sticky secure MAC addresses.
+ The protect and restrict options cannot be simultaneously enabled on an interface.
(Reference: http://www.cisco.com/en/US/docs/switches/lan/catalyst3550/software/release/12.1_19_ea1
/configuration/guide/swtrafc.html)
Q39. - (Topic 4)
What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?
A. defines the destination IP address that is used in all broadcast packets on DCLI 202
B. defines the source IP address that is used in all broadcast packets on DCLI 202
C. defines the DLCI on which packets from the 192.168.1.2 IP address are received
D. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address
Answer: D
Explanation:
This command identifies the DLCI that should be used for all packets destined to the 192.168.1.2 address. In this case, DLCI 202 should be used.
Q40. - (Topic 3)
Refer to the exhibit.
What can be determined about the router from the console output?
A. No configuration file was found in NVRAM.
B. No configuration file was found in flash.
C. No configuration file was found in the PCMCIA card.
D. Configuration file is normal and will load in 15 seconds.
Answer: A
Explanation:
When no startup configuration file is found in NVRAM, the System Configuration Dialog will appear to ask if we want to enter the initial configuration dialog or not.