Master the 200 125 ccna v3 0 CCNA Cisco Certified Network Associate CCNA (v3.0) content and be ready for exam day success quickly with this Pass4sure ccna 200 125 dumps exam fees. We guarantee it!We make it a reality and give you real ccna 200 120 vs 200 125 questions in our Cisco 200 125 ccna v3 0 braindumps.Latest 100% VALID Cisco ccna 200 125 ebook Exam Questions Dumps at below page. You can use our Cisco ccna 200 125 book braindumps and pass your exam.

Q141.  - (Topic 5)

The network administrator needs to address seven LANs. RIP version 1 is the only routing protocol in use on the network and subnet 0 is not being used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?

A. 8

B. 6

C. 30

D. 32

E. 14

F. 16

Answer: C

Explanation:

Since there is one class C network that means 256 total IP addresses. Since we need 7 LAN blocks and we cannot use the first one (subnet 0) we take 256/8=32 hosts. However, since we need to reserve the network and broadcast addresses for each of these subnets, only 30 total IP addresses are usable.


Q142.  - (Topic 8)

Which component of the routing table ranks routing protocols according to their preferences?

A. administrative distance

B. next hop

C. metric

D. routing protocol code

Answer: A

Explanation:

Administrative distance - This is the measure of trustworthiness of the source of the route. If a router learns about a destination from more than one routing protocol, administrative distance is compared and the preference is given to the routes with lower administrative distance. In other words, it is the believability of the source of the route.


Q143.  - (Topic 8)

Which switching method duplicates the first six bytes of a frame before making a switching decision?

A. fragment-free switching

B. store and-forward switching

C. cut through switching

D. ASIC switching

Answer: C

Explanation: Cut and Through method has lowest latency. In this method Switch only read first six bytes from frame after the preamble. These six bytes are the destination address of frame. This is the fastest method of switching. This method also processes invalid frames. Only advantage of this method is speed.


Q144.  - (Topic 4)

Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications?

A. RSA

B. L2TP

C. IPsec

D. PPTP

Answer: C

Explanation:

IPSec is a framework of open standards that provides data confidentiality, data integrity, and data authentication between participating peers at the IP layer. IPSec can be used to protect one or more data flows between IPSec peers.


Q145.  - (Topic 3)

Refer to the exhibit.

The speed of all serial links is E1 and the speed of all Ethernet links is 100 Mb/s. A static route will be established on the Manchester router to direct traffic toward the Internet over the most direct path available. What configuration on the Manchester router will establish a route toward the Internet for traffic that originates from workstations on the Manchester LAN?

A. ip route 0.0.0.0 255.255.255.0 172.16.100.2

B. ip route 0.0.0.0 0.0.0.0 128.107.1.1

C. ip route 0.0.0.0 255.255.255.252 128.107.1.1

D. ip route 0.0.0.0 0.0.0.0 172.16.100.1

E. ip route 0.0.0.0 0.0.0.0 172.16.100.2

F. ip route 0.0.0.0 255.255.255.255 172.16.100.2

Answer: E

Explanation:

We use default routing to send packets with a remote destination network not in the routing table to the next-hop router. You should generally only use default routing on stub networks—those with only one exit path out of the network.

According to exhibit, all traffic towards Internet that originates from workstations should forward to Router R1.

Syntax for default route is:

ip route <Remote_Network> <Netmask> <Next_Hop_Address>.


Q146.  - (Topic 8)

Which statement about LLDP is true?

A. It is a Cisco proprietary protocol.

B. It is configured in global configuration mode.

C. The LLDP update frequency is a fixed value.

D. It runs over the transport layer.

Answer: B


Q147.  - (Topic 8)

Scenario:

You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.

Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.

NAT is enabled on router R1.

The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.

R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.

You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.

Examine the DHCP configuration between R2 and R3; R2 is configured as the DHCP server and R3 as the client. What is the reason R3 is not receiving the IP address via DHCP?

A. On R2. The network statement In the DHCP pool configuration is incorrectly configured.

B. On R3. DHCP is not enabled on the interface that is connected to R2.

C. On R2, the interface that is connected to R3 is in shutdown condition.

D. On R3, the interface that is connected to R2 is in shutdown condition.

Answer: B

Explanation:

Please check the below:


Q148.  - (Topic 7)

In which circumstance are multiple copies of the same unicast frame likely to be transmitted in a switched LAN?

A. during high traffic periods

B. after broken links are re-established

C. when upper-layer protocols require high reliability

D. in an improperly implemented redundant topology

E. when a dual ring topology is in use

Answer: D

Explanation:

If we connect two switches via 2 or more links and do not enable STP on these switches then a loop (which creates multiple copies of the same unicast frame) will occur. It is an example of an improperly implemented redundant topology.


Q149.  - (Topic 8)

Why did Branch1 router lose WAN connectivity with R1 router?

A. The IP address is misconfigured on PPP multilink interface on the Branch1 router.

B. The PPP multilink group is misconfigured on the £ranch1 serial interfaces.

C. The PPP multilink group is misconfigured on the R1 serial interfaces.

D. The Branch1 serial interfaces are placed in a shutdown condition.

Answer: A


Q150.  - (Topic 5)

What is the first 24 bits in a MAC address called?

A. NIC

B. BIA

C. OUI

D. VAI

Answer: C

Explanation:

An Organizationally Unique Identifier (OUI) is a 24-bit number that uniquely identifies a vendor, manufacturer, or other organization globally or worldwide.

They are used as the first 24 nits of the MAC address to uniquely identify a particular piece of equipment.