Want to know Actualtests 200-125 Exam practice test features? Want to lear more about Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) certification experience? Study Pinpoint Cisco 200-125 answers to Refresh 200-125 questions at Actualtests. Gat a success with an absolute guarantee to pass Cisco 200-125 (CCNA Cisco Certified Network Associate CCNA (v3.0)) test on your first attempt.
2021 Apr 200-125 pdf exam
Q121. - (Topic 3)
A router receives information about network 192.168.10.0/24 from multiple sources. What will the router consider the most reliable information about the path to that network?
A. a directly connected interface with an address of 192.168.10.254/24
B. a static route to network 192.168.10.0/24
C. a RIP update for network 192.168.10.0/24
D. an OSPF update for network 192.168.0.0/16
E. a default route with a next hop address of 192.168.10.1
F. a static route to network 192.168.10.0/24 with a local serial interface configured as the next hop
Answer: A
Explanation:
When there is more than one way to reach a destination, it will choose the best one based on a couple of things. First, it will choose the route that has the longest match; meaning the most specific route. So, in this case the /24 routes will be chosen over the /16 routes. Next, from all the /24 routes it will choose the one with the lowest administrative distance. Directly connected routes have an AD of 1 so this will be the route chosen.
Q122. - (Topic 8)
Which option describes how a switch in rapid PVST+ mode responds to a topology change?
A. It immediately deletes dynamic MAC addresses that were learned by all ports on the switch.
B. It sets a timer to delete all MAC addresses that were learned dynamically by ports in the same STP instance.
C. It sets a timer to delete dynamic MAC addresses that were learned by all ports on the switch.
D. It immediately deletes all MAC addresses that were learned dynamically by ports in the same STP instance.
Answer: D
Explanation:
Rapid PVST+This spanning-tree mode is the same as PVST+ except that is uses a rapid convergence based on the IEEE 802.1w standard. To provide rapid convergence, the rapid PVST+ immediately deletes dynamically learned MAC address entries on a per-port basis upon receiving a topology change. By contrast, PVST+ uses a short aging time for dynamically learned MAC address entries.
The rapid PVST+ uses the same configuration as PVST+ (except where noted), and the switch needs only minimal extra configuration. The benefit of rapid PVST+ is that you can migrate a large PVST+ install base to rapid PVST+ without having to learn the complexities of the MSTP configuration and without having to reprovision your network. In rapid-PVST+ mode, each VLAN runs its own spanning-tree instance up to the maximum supported.
Q123. - (Topic 7)
Scenario
Refer to the topology. Your company has connected the routers R1, R2, and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
The loopback interfaces on R4 with the IP addresses of 10.4.4.4/32, 10.4.4.5/32, and 10.4.4.6/32 are not appearing in the routing table of R5. Why are the interfaces missing?
A. The interfaces are shutdown, so they are not being advertised.
B. R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
C. Automatic summarization is enabled, so only the 10.0.0.0 network is displayed.
D. The loopback addresses haven't been advertised, and the network command is missing on R4.
Answer: B
Explanation:
For an EIGRP neighbor to form, the following must match:
- Neighbors must be in the same subnet
- K values
- AS numbers
- Authentication method and key strings
Here, we see that R4 is configured for EIGRP AS 2, when it should be AS 1.
Topic 8, Mixed Questions
316. - (Topic 8)
Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.
Answer: A
Explanation: IP routing must be enables to allow the two hosts to communicate with each other with default configuration.
http://www.cisco.com/c/en/us/support/docs/lan-switching/inter-vlan-routing/41860-howto-L3-intervlanrouting.html
Q124. - (Topic 8)
On which type of device is every port in the same collision domain?
A. a router
B. a Layer 2 switch
C. a hub
Answer: C
Explanation: Collision domainA collision domain is, as the name implies, a part of a
network where packet collisions can occur. A collision occurs when two devices send a packet at the same time on the shared network segment. The packets collide and both devices must send the packets again, which reduces network efficiency. Collisions are often in a hub environment, because each port on a hub is in the same collision domain. By contrast, each port on a bridge, a switch or a router is in a separate collision domain.
Q125. - (Topic 5)
Which IPv6 address is the equivalent of the IPv4 interface loopback address 127.0.0.1?
A. ::1
B. ::
C. 2000::/3
D. 0::/10
Answer: A
Explanation:
In IPv6 the loopback address is written as, ::1
This is a 128bit number, with the first 127 bits being '0' and the 128th bit being '1'. It's just a single address, so could also be written as ::1/128.
Renew 200-125 test engine:
Q126. - (Topic 8)
when you troubleshoot an IPv4 connectivity issue on a router, which three router configuration checks you must perform?
A. Verify that the router interface IP address IP address is correct.
B. Verify that the DNS is configured correctly.
C. Verify that the router and the host use the same subnet mask.
D. Verify that the router firmware is up-to-date.
E. Verify that a default route is configured.
F. Verify that the route appears in the routing table
Answer: A,B,F
Q127. - (Topic 3)
Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Answer: D,F
Explanation:
This question is to examine the conditions for OSPF to create neighborhood.
So as to make the two routers become neighbors, each router must be matched with the following items:
1. The area ID and its types;
2. Hello and failure time interval timer;
3. OSPF Password (Optional).
Q128. - (Topic 7)
What Netflow component can be applied to an interface to track IPv4 traffic?
A. flow monitor
B. flow record
C. flow sampler
D. flow exporter
Answer: A
Explanation:
Flow monitors are the Flexible NetFlow component that is applied to interfaces to perform network traffic monitoring. Flow monitors consist of a record and a cache. You add the record to the flow monitor after you create the flow monitor. The flow monitor cache is automatically created at the time the flow monitor is applied to the first interface. Flow data
is collected from the network traffic during the monitoring process based on the key and nonkey fields in the record, which is configured for the flow monitor and stored in the flow monitor cache.
For example, the following example creates a flow monitor named FLOW-MONITOR-1 and enters Flexible NetFlow flow monitor configuration mode:
Router(config)# flow monitor FLOW-MONITOR-1 Router(config-flow-monitor)#
Q129. - (Topic 8)
Which standards-based First Hop Redundancy Protocol is a Cisco supported alternative to Hot Standby Router Protocol?
A. VRRP
B. GLBP
C. TFTP
D. DHCP
Answer: A
Q130. - (Topic 5)
Which three features are added in SNMPv3 over SNMPv2?
A. Message Integrity
B. Compression
C. Authentication
D. Encryption
E. Error Detection
Answer: A,C,D
Explanation:
Cisco IOS software supports the following versions of SNMP:
+ SNMPv1 – The Simple Network Management Protocol: A Full Internet Standard, defined in RFC 1157. (RFC 1157 replaces the earlier versions that were published as RFC 1067 and RFC 1098.) Security is based on community strings.
+ SNMPv2c – The community-string based Administrative Framework for SNMPv2. SNMPv2c (the “c” stands for “community”) is an Experimental Internet Protocol defined in RFC 1901, RFC 1905, and RFC 1906. SNMPv2c is an update of the protocol operations and data types of SNMPv2p (SNMPv2 Classic), and uses the community-based security model of SNMPv1.
+ SNMPv3 – Version 3 of SNMP. SNMPv3 is an interoperable standards-based protocol defined in RFCs 2273 to 2275. SNMPv3 provides secure access to devices by a combination of authenticating and encrypting packets over the network. The security features provided in SNMPv3 are as follows:
– Message integrity: Ensuring that a packet has not been tampered with in transit.
– Authentication: Determining that the message is from a valid source.
– Encryption: Scrambling the contents of a packet prevent it from being learned by an unauthorized source.