It is more faster and easier to pass the Cisco ccna routing and switching 200 125 official cert guide library exam by using Highest Quality Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) questuins and answers. Immediate access to the Leading ccna 200 125 torrent Exam and find the same core area ccna 200 125 pdf questions with professionally verified answers, then PASS your exam with a high score now.

P.S. Highest Quality 200-125 keys are available on Google Drive, GET MORE: https://drive.google.com/open?id=1TVPbOp7ab9OckkT77rZa87L3hf9XaR7B


New Cisco 200-125 Exam Dumps Collection (Question 7 - Question 14)

Question No: 7

In a GLBP network, who is responsible for the ARP request?

A. AVF

B. AVG

C. Active Router

D. Standby Router

Answer: B

Explanation:

Members of a GLBP group elect one gateway to be the active virtual gateway (AVG) for that group. Other group members provide backup for the AVG in the event that the AVG becomes unavailable. The AVG assigns a virtual MAC address to each member of the GLBP group. Each gateway assumes responsibility for forwarding packets sent to the virtual MAC address assigned to it by the AVG. These gateways are known as active virtual forwarders (AVFs) for their virtual MAC address.

The AVG is responsible for answering Address Resolution Protocol (ARP) requests for the virtual IP address. Load sharing is achieved by the AVG replying to the ARP requests with different virtual MAC addresses.

Reference: http://www.cisco.com/en/US/docs/ios/12_2t/12_2t15/feature/guide/ft_glbp.html


Question No: 8

What command instructs the device to timestamp Syslog debug messages in milliseconds?

A. service timestamps log datetime localtime<input type

B. service timestamps debug datetime msec<input type

C. service timestamps debug datetime localtime<input type

D. service timestamps log datetime msec

Answer: B

Explanation:

Enable millisecond (msec) timestamps using the service timestamps command: router(config)#service timestamps debug datetime msec.

router(config)#service timestamps log datetime msec The u201cservice timestamps debugu201d.

command configures the system to apply a time stamp to debugging messages. The time- stamp format fordatetimeisMMM DD HH:MM:SS, whereMMMis the month,DDis the date,HHis the hour (in 24-hour notation),MMis the minute, andSSis the second. With the additional keywordmsec, the system includes milliseconds in the time stamp, in the formatHH:DD:MM:SS.mmm, where .mmmis milliseconds.


Question No: 9

What is the first 24 bits in a MAC address called?

A. NIC

B. BIA

C. OUI

D. VAI

Answer: C

Explanation:

An Organizationally Unique Identifier (OUI) is a 24-bit number that uniquely identifies a vendor, manufacturer, or other organization globally or worldwide.

They are used as the first 24 nits of the MAC address to uniquely identify a particular piece of equipment.


Question No: 10

Which set of commands is recommended to prevent the use of a hub in the access layer?

A. switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1

B. switch(config-if)#switchport mode trunk

switch(config-if)#switchport port-security mac-address 1

C. switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1

D. switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1

Answer: C

Explanation:

This question is to examine the layer 2 security configuration.

In order to satisfy the requirements of this question, you should perform the following

configurations in the interface mode:

First, configure the interface mode as the access mode

Second, enable the port security and set the maximum number of connections to 1.


Question No: 11

CORRECT TEXTA network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed.

The task is to create and apply an access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted.

Access to the router CLI can be gained by clicking on the appropriate host. All passwords have been temporarily set to "cisco".

The Core connection uses an IP address of 198.18.196.65.

The computers in the Hosts LAN have been assigned addresses of 192.168.33.1 - 192.168.33.254

u2711 host A 192.168.33.1

u2711 host B 192.168.33.2

u2711 host C 192.168.33.3

u2711 host D 192.168.33.4

The servers in the Server LAN have been assigned addresses of 172.22.242.17 - 172.22.242.30.

The Finance Web Server is assigned an IP address of 172.22.242.23.

Answer:

Select the console on Corp1 router Configuring ACL

Corp1>enable Corp1#configure terminal

comment: To permit only Host C (192.168.33.3){source addr} to access finance server address (172.22.242.23) {destination addr} on port number 80 (web) Corp1(config)#access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80 comment: To deny any source to access finance server address (172.22.242.23)

{destination addr} on port number 80 (web)

Corp1(config)#access-list 100 deny tcp any host 172.22.242.23 eq 80

comment: To permit ip protocol from any source to access any destination because of the implicit deny any any statement at the end of ACL.

Corp1(config)#access-list 100 permit ip any any Applying the ACL on the Interface

comment: Check show ip interface brief command to identify the interface type and number by checking the IP address configured.

Corp1(config)#interface fa 0/1

If the ip address configured already is incorrect as well as the subnet mask. This should be corrected in order ACL to work

type this commands at interface mode :

no ip address 192.x.x.x 255.x.x.x (removes incorrect configured ipaddress and subnet mask)

Configure Correct IP Address and subnet mask:

ip address 172.22.242.30 255.255.255.240 ( range of address specified going to server is given as 172.22.242.17 - 172.22.242.30 )

Comment: Place the ACL to check for packets going outside the interface towards the

finance web server.

Corp1(config-if)#ip access-group 100 out Corp1(config-if)#end

Important: To save your running config to startup before exit. Corp1#copy running-config startup-config

Verifying the Configuration:

Step1: show ip interface brief command identifies the interface on which to apply access list.

Step2: Click on each host A, B, C, & D. Host opens a web browser page, Select address box of the web browser and type the ip address of finance web server (172.22.242.23) to test whether it permits /deny access to the finance web Server.

Step 3: Only Host C (192.168.33.3) has access to the server. If the other host can also access then maybe something went wrong in your configuration. Check whether you configured correctly and in order.

Step 4: If only Host C (192.168.33.3) can access the Finance Web Server you can click on NEXT button to successfully submit the ACL SIM.


Question No: 12

Scenario

Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.

You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.

An OSPF neighbor adjacency is not formed between R3 in the main office and R6 in the Branch3 office. What is causing the problem?

A. There is an area ID mismatch.

B. There is a PPP authentication issue; the username is not configured on R3 and R6.

C. There is an OSPF hello and dead interval mismatch.

D. The R3 router ID is configured on R6.

Answer: D

Explanation:

Using the show running-config command we see that R6 has been incorrectly configured with the same router ID as R3 under the router OSPF process.


Question No: 13

Refer to the exhibit.

If the devices produced the given output, what is the cause of the EtherChannel problem?

A. SW1's Fa0/1 interface is administratively shut down.

B. There is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.

C. There is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.

D. There is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.

Answer: D

Explanation:

You must configure all interfaces in an EtherChannel to operate at the same speeds and duplex modes. Based on the output shown, SW1 is configured to run at 10Mb while SW2 is operating at 100 Mb.


Question No: 14

What is the default Syslog facility level?

A. local4

B. local5

C. local6

D. local7

Answer: D

Explanation:

By default, Cisco IOS devices, CatOS switches, and VPN 3000 Concentrators use facility local7 while Cisco PIX Firewalls use local4 to send syslog messages. Moreover, most Cisco devices provide options to change the facility level from their default value.

Reference: http://www.ciscopress.com/articles/article.asp?p=426638


100% Leading Cisco 200-125 Questions & Answers shared by Allfreedumps, Get HERE: https://www.allfreedumps.com/200-125-dumps.html (New 573 Q&As)