100% Correct 200-125 vce Reviews & Tips

Act now and download your Cisco 200-125 test today! Do not waste time for the worthless Cisco 200-125 tutorials. Download Far out Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) exam with real questions and answers and begin to learn Cisco 200-125 with a classic professional.

2021 Oct 200-125 actual test

Q21. - (Topic 4)

Which three elements must be used when you configure a router interface for VLAN trunking? (Choose three.)

A. one physical interface for each subinterface

B. one IP network or subnetwork for each subinterface

C. a management domain for each subinterface

D. subinterface encapsulation identifiers that match VLAN tags

E. one subinterface per VLAN

F. subinterface numbering that matches VLAN tags

Answer: B,D,E

Q22. - (Topic 7)

Refer to the exhibit.

A network administrator attempts to ping Host2 from Host1 and receives the results that are shown. What is the problem?

A. The link between Host1 and Switch1 is down.

B. TCP/IP is not functioning on Host1

C. The link between Router1 and Router2 is down.

D. The default gateway on Host1 is incorrect.

E. Interface Fa0/0 on Router1 is shutdown.

F. The link between Switch1 and Router1 is down.

Answer: C

Q23. - (Topic 4)

Which two locations can be configured as a source for the IOS image in the boot system command? (Choose two.)

A. RAM

B. NVRAM

C. flash memory

D. HTTP server

E. TFTP server

F. Telnet server

Answer: C,E

Q24. - (Topic 2)

A switch is configured with all ports assigned to VLAN 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?

A. More collision domains will be created.

B. IP address utilization will be more efficient.

C. More bandwidth will be required than was needed previously.

D. An additional broadcast domain will be created.

Answer: D

Q25. - (Topic 3)

Which IPv6 address is the all-router multicast group?

A. FF02::1

B. FF02::2

C. FF02::3

D. FF02::4

Answer: B

200-125 exam topics

Updated 200-125 practice test:

Q26. - (Topic 8)

The output of the show frame-relay pvc command shows "PVC STATUS = INACTIVE". What does this mean?

A. The PVC is configured correctly and is operating normally, but no data packets have been detected for more than five minutes.

B. The PVC is configured correctly, is operating normally, and is no longer actively seeking the address of the remote router.

C. The PVC is configured correctly, is operating normally, and is waiting for interesting traffic to trigger a call to the remote router.

D. The PVC is configured correctly on the local switch, but there is a problem on the remote end of the PVC.

E. The PVC is not configured on the local switch.

Answer: D

Q27. - (Topic 5)

What command instructs the device to timestamp Syslog debug messages in milliseconds?

A. service timestamps log datetime localtime

B. service timestamps debug datetime msec

C. service timestamps debug datetime localtime

D. service timestamps log datetime msec

Answer: B

Q28. DRAG DROP - (Topic 4)

Answer:

Q29. - (Topic 1)

Refer to the exhibit.

Based on the information given, which switch will be elected root bridge and why?

A. Switch A, because it has the lowest MAC address

B. Switch A, because it is the most centrally located switch

C. Switch B, because it has the highest MAC address

D. Switch C, because it is the most centrally located switch

E. Switch C, because it has the lowest priority

F. Switch D, because it has the highest priority

Answer: E

Q30. - (Topic 2)

Refer to the exhibit.

A network administrator is configuring an EtherChannel between SW1 and SW2. The SW1 configuration is shown. What is the correct configuration for SW2?

A. interface FastEthernet 0/1

channel-group 1 mode active