Q41. An AP was reset while working on the correct association to a Cisco WCS version 7.0.
Which item was cleared during the reset?
A. static IP address
B. the location ID of the AP
C. WLC primary, secondary, tertiary
D. AP name
E. certificate
F. Nothing was cleared.
Answer: F
Q42. An AP using version 7.0 MR1 broadcasts a Layer 3 CAPWAP discovery message on the local IP subnet. Which step does the AP take next?
A. Determine if the controller responses include the primary controller.
B. Determine if the controller responses include the master controller.
C. Send a discovery request using DHCP option 43.
D. Send a discovery request using DNS.
E. Send a discovery request using locally stored information on the AP.
F. Send a discovery request using OTAP.
Answer: E
Q43. A company wants to implement wireless in all 20 remote office locations and wants centralized management of these remote sites. What application would meet the requirements?
A. Control And Provisioning of Wireless Access Points
B. Cisco point- to multi-point wireless bridging
C. Cisco autonomous access points in FlexConnect mode
D. Split MAC architecture utilizing LWAPP and WLC
Answer: D
Q44. Which statement best describes the ability of a wireless client to access and transmit a data frame to an AP?
A. The client listens to the media until polled by the AP using PCF to send its data.
B. The client listens to the media until a data frame is finished, at which time it transmits, unless a collision of data frames has occurred.
C. The client uses random countdown timers to start the transmission of a data frame.
D. The client listens to the media and countdown timers to start the transmission of a data frame.
Answer: D
Q45. When using the CLI command eping, configured for auto-anchor mobility wireless guest access, which type of packet is tested?
A. data packets
B. mobility unencrypted packets
C. mobility encrypted packets
D. SNMP control packets
E. NTP control packets
Answer: A
Q46. Which protocol is used for Cisco WCS to communicate with Cisco WLC?
A. SNMP
B. CAPWAP
C. HTTPS
D. SSH
Answer: A
Q47. An installation uses a 21dBi parabolic dish. It is connected to the 802.11n radio via low loss antenna coax rated at 4dB loss/100 feet. After testing, it has been determined that 2mW of power will be lost in the cable. An EIRP producing 200mW is desired. What should the transmit power be set to?
A. 8mW
B. 3dBm
C. 3.16mW
D. 5mW
Answer: C
Q48. You have a lightweight AP that has been moved to a new subnet and has become stranded because DNS and DHCP servers are unavailable. The AP cannot connect to the controller.
When connected to the console port, which three minimum parameters must you configure? (Choose three.)
A. AP IP address
B. controller name
C. AP hostname
D. default gateway IP address
E. controller IP address
F. username and password
Answer: A,D,E
Q49. A WLAN deployment uses a combination of Cisco Aironet 1260 APs and multiple Cisco 5500 Wireless LAN Controllers to provide wireless LAN access to end-users. The network administrator has decided to use DHCP Option 43 to enable the APs to discover the wireless LAN controllers.
When configuring the DHCP scope, which format should be used for the Cisco WLC addresses?
A. a comma-separated ASCII string of Cisco WLC AP-manager addresses
B. a comma-separated ASCII string of Cisco WLC management addresses
C. a comma-separated ASCII string of Cisco WLC virtual IP addresses
D. a hexadecimal string of Cisco WLC AP-manager addresses
E. a hexadecimal string of Cisco WLC management addresses
F. a hexadecimal string of Cisco WLC virtual IP addresses
Answer: E
Q50. Which RRM feature allows an access point to avoid non-IEEE 802.11 interference?
A. DCA
B. TPC
C. RF groups
D. coverage hole detection
Answer: A