100% Guarantee of 300 075 vce free exam materials and answers for Cisco certification for examinee, Real Success Guaranteed with Updated 300 075 pdf pdf dumps vce Materials. 100% PASS Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) exam Today!
Q11. Refer to the exhibit.
When the user of a phone registered to the Cisco Unified Communications Manager places a call to 3001 when the SAF network is down, what happens?
A. The call fails.
B. The call is rerouted to the PSTN with the constructed PSTN number as +442288223001
C. The call is rerouted to the PSTN with the constructed PSTN number as 442288223001
D. The call is rerouted to the PSTN with the constructed PSTN number as 0002288223001
E. The call is rerouted to the PSTN with the constructed PSTN number as +0002288223001
Answer: A
Explanation:
Incorrect Answer: B, C, D When the SAF forwarder loses network connection with its call-control entity, the SAF forwarder withdraws those learned patterns that were published by the call control entity. In this case, CCD requesting service marks those learned patterns as unreachable via IP, and the calls get routed through the PSTN gateway. Link:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_6_1/ccmfeat/fscallcontrol discovery.html
Q12. Which Cisco IOS command is used to verify that the Cisco Unified Communications Manager Express has registered with the SAF Forwarder?
A. show eigrp service-family ipv4 clients
B. show eigrp address-family ipv4 clients
C. show voice saf dndb all
D. show saf registration
E. show ip saf registration
Answer: A
Explanation:
Incorrect Answer: B, C, D, E show eigrp service-family ipv4 clients Displays information from the EIGRP IPv4 service-family results.
Q13. Which two actions ensure that the call load from Cisco TelePresence Video Communication Server to a Cisco Unified Communications Manager cluster is shared across Unified CM nodes? (Choose two.)
A. Create a neighbor zone in VCS with the Unified CM nodes listed as location peer addresses.
B. Create a single traversal client zone in VCS with the Unified CM nodes listed as location peer addresses.
C. Create one neighbor zone in VCS for each Unified CM node.
D. Create a VCS DNS zone and configure one DNS SRV record per Unified CM node.
E. In VCS set Unified Communications mode to Mobile and remote access and configure each Unified CM node.
Answer: A,D
Q14. Which command can be used to manually send the MGCP gateway to register with the secondary Cisco Unified Communications Manager server?
A. ccm-manager switchover-to-backup
B. mgcp use backup
C. ccm-manager register backup
D. not supported
Answer: A
Q15. Assume that local route groups are configured. When an IP phone moves from one device mobility group to another, which two configuration components are not changed? (Choose two.)
A. IP subnet
B. user settings
C. SRST reference
D. region
E. phone button settings
Answer: B,E
Explanation:
Incorrect Answer: A, C, D Although the phone may have moved from one subnet to another, the physical location and associated services have not changed. Link:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/7_1_2/ccmfeat/fsdevmob.html#wp1137460
Q16. Refer to the exhibit.
The H.323 Gateway is showing status “unknown”. Which statement is true?
A. The gateway must be reset in Cisco Unified Communications Manager.
B. The no gateway command followed by the gateway command must be issued in Cisco IOS.
C. The mgcp commands must be removed.
D. H.323 gateways do not register with Cisco Unified Communications Manager H.323 gateways always show status "Unknown".
E. VUAN 1 20 may be down and so the H.323 gateway appears offline to the Cisco Unified Communications Manager
Answer: D
Explanation:
Incorrect Answer: A, B, C, E
After a gateway is registered with Cisco Unified Communications Manager, gateway registration status may display in Cisco Unified Communications Manager Administration as unknown.
Link:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucmbe/admin/8_6_1/ccmcfg/b06gtway. html
Q17. Which remote-site redundancy technology fails over to POTS dial peers from the Cisco Unified Communications Manager dial plan during a WAN failure?
A. MGCP fallback
B. H.323 fallback
C. SCCP fallback
D. SIP fallback
Answer: A
Q18. Refer to the exhibit.
With the Mobile Connect feature configured, when the PSTN phone calls the Enterprise user at extension 3001, the Enterprise user's mobile phone does not ring. Which CSS is responsible for ensuring that the correct partitions are accessed when calls are sent to the Enterprise user's mobile phone?
A. the gateway CSS
B. the Phone Device CSS
C. the Remote Destination Profile CSS
D. the Remote Destination Profile Rerouting CSS
E. the Phone Line (DN)CSS
Answer: D
Explanation:
Incorrect Answer: A, B, C, E
Ensure that the gateway that is configured for routing mobile calls is assigned to the partition that belongs to the Rerouting Calling Search Space. Cisco Unified Communications Manager determines how to route calls based on the remote destination number and the Rerouting Calling Search Space. Link: http://www.cisco.com/en/US/docs/voice_ip_comm/cucmbe/admin/8_6_1/ccmfeat/fsmobmgr .html
Q19. While operating in SRST, what is needed to route calls outside of the remote site location to the PSTN?
A. SIP trunk
B. CallManager route patterns
C. translation patterns
D. POTS dial peers
E. VOIP dial peers
Answer: D
Explanation:
Incorrect Answer: A, B, C, E
in time of srst configuration on router, please configure a dial-peer so that call flow in SRST mode.
Q20. Refer to the exhibit.
Assume that the HQ phones have access to the HQ partition, and BR phones have access to the BR partition. Which set of implementations would best address the overlapping directory number extensions for intersite (WAN) calling between the HQ site and the BR site?
A. Configure a route pattern 8222.[12]XXX for site HQ, and assign it to partition HQ. Configure the called party DDI of Predot.Configure a route pattern for site BR 8111.[1-3]XXX, and assign it to partition BR. Configure called party DDI Predot.Use the local gateway at each site. Prefix the appropriate site code for the calling number.
B. Configure a single route pattern for both sites 8[12,12,12].[1-32]XXX. Use a route list that contains the local route group for each site. Prefix the appropriate site code for the calling number.
C. Configure a translation pattern 8222.[12]XXX for site HQ, and assign it to partition HQ. Use a CSS that contains the partitions for BR phones.Configure a translation pattern 8111.[1-3]XXX for site BR, and assign it to partition BR. Use a CSS that contains the partitions for HQ phones.For both translation patterns, configure the called party DDI of Predot. Prefix the appropriate site code for the calling number.
D. Configure a translation pattern 8222.[12]XXX for site HQ, and assign it to partition BR. Use a CSS that contains the partitions for HQ phones.Configure a translation pattern 8111.[1-3]XXX for site BR, and assign it to partition HQ. Use a CSS that contains the partitions for BR phones.For both translation patterns, configure the called party DDI of Predot. Prefix the appropriate site code for the calling number.
Answer: C