It is more faster and easier to pass the by using . Immediate access to the and find the same core area with professionally verified answers, then PASS your exam with a high score now.

Free demo questions for Cisco 300-180 Exam Dumps Below:

NEW QUESTION 1
After removing a VMM domain from an EPG, you discover that the associated virtual port groups remain in the VMware vCenter configuration. What causes the virtual port groups to persist in the configuration?

  • A. The MAC addresses that are learned by the ports of the spine switches are incorrect.
  • B. The port groups are being used by a virtual machine network adapter.
  • C. The MAC addresses that are learned by the ports of the leaf switches are incorrect
  • D. There is a mismatch between the data center name in vCenter and the VMM controller policy.

Answer: B

NEW QUESTION 2
You configure a boot from SAN multipath environment that uses an EMC storage array. The host is registered on the array. Other hosts that have the same WWPN also appear to logged in. which action resolves the issue?

  • A. Remove the local disks that are connected to the blade.
  • B. Ensure that the storage array is cable correctly.
  • C. Explicitly register all the paths on the storage array.
  • D. Configure that LUN masking is applied correctly.

Answer: C

NEW QUESTION 3
In an IP storage environment, what occurs if you apply a service profile to a server that has an Ethernet-only mezzanine card?

  • A. The storage adapter is not visible to the OS
  • B. A blade association occurs,
  • C. WWPN and WWNN are selected from the default pool
  • D. The OS fails to boot

Answer: B

NEW QUESTION 4
Refer to the exhibit. The two switches are stuck in the EXCHANGE and EXSTART states. Which option is a possible cause of the issue?
300-180 dumps exhibit

  • A. The subnet mask is mismatched.
  • B. The interfaces are not connected.
  • C. The MTU is mismatched.
  • D. The IP address of the OSPF process is incorrect.

Answer: C

NEW QUESTION 5
On a Cisco Nexus 5500 Series Switch, the VFC is stuck in the initializing state. Which QoS statements must be configured for FCoE to operate?

  • A. system qosservice-policy type qos input fcoe-default-in-policy service-policy type queuing input fcoe-default-in-policy service-policy type queuing output fcoe-default-out-policy service-policy type network-qos fcoe-default-nq-policy
  • B. system qosservice-policy type qos input fcoe-default-in-policy service-policy type queuing input fcoe-default-in-policy service-policy type qos input default-in-policyservice-policy type network-qos default-nq-policy
  • C. system qosservice-policy type qos input default-in-policy service-policy type queuing input default-in-policy service-policy type queuing output default-out-policy service-policy type network-qos default-nq-policy
  • D. system qosservice-policy type qos input default-in-policy service-policy type queuing input default-in-policyservice-policy type queuing output fcoe-default-out-policy service-policy type network-qos fcoe-default-nq-policy

Answer: A

NEW QUESTION 6
Refer to the exhibit.
300-180 dumps exhibit
Which description of the output is true?

  • A. Two VTEPs are in the VEM.
  • B. Two VTEP table versions exist.
  • C. Two VTEPs are in the VSM.
  • D. One designated VTEP is in the bridge domain.

Answer: C

NEW QUESTION 7
Refer to the exhibit.
300-180 dumps exhibit
VSAN traffic is not being routed through SAN fabric. Which action is helpful to resolve the problem?

  • A. Make sure that the FSPF hello interval value matches on both switches.
  • B. Change the FSPF hello timer back to the default of 5 seconds.
  • C. Make sure that the FSPF hello timers are different so that they do not compete.
  • D. Make sure that the FSPF dead timers are both set to 0.

Answer: A

NEW QUESTION 8
A customer is trying to boot an operating system installed on a Cisco UCS B-Series blade server after a RAID1 cluster migration. The RAID LUN remains in inactive state during and after the service profile association and the server does not boot. What is the cause of this problem?

  • A. RAID1 is not supported in cluster migration mode on a Cisco UCS B-Series blade server.
  • B. The local disk configuration policy in the service profile on the server is configured with Any Configuration mode rather than RAID1.
  • C. The server needs to be booted via SAN in cluster migration to support RAID1.
  • D. The Cisco UCS B-Series blade server has older firmware that needs to be updated first.

Answer: B

NEW QUESTION 9
Refer to the exhibit.
300-180 dumps exhibit
Customer encounters the problem as shown in the exhibit. What is the cause of the problem?

  • A. No server was requested or received by the FLOGI database.
  • B. One external link must be up for server interface to be up.
  • C. Multiple external links must be up for the server to come up.
  • D. Internal links are down and must be up for the server interface to be up.

Answer: A

NEW QUESTION 10
When using a Cisco Nexus 5500 and Cisco Nexus 7000 Series Switch, how can a port channel interface be configured?

  • A. Layer 3 interface
  • B. Layer 3 interface in non-admin VDC only
  • C. Layer 3 interface in admin VDC only
  • D. Layer 3 interface in VDC 1 only

Answer: A

NEW QUESTION 11
One of your Cisco Nexus Series interfaces has become errdisabled with the error message "DCX-No ACK in 100 PDUs". How often are these acknowledgements exchanged?

  • A. 15 seconds
  • B. 30 seconds
  • C. 45 seconds
  • D. 60 seconds

Answer: B

NEW QUESTION 12
Refer to the exhibit.
300-180 dumps exhibit
You are troubleshooting Dynamic ARP inspection.
Which command set correctly configures the access list to be used by ARP inspection?

  • A. N7k1-core(config)# mac access-list ARP-FilterNk1-Core(config-mac-acl) # 1 permit mac 5031. 3ca2.1bb3 0000.0000 any
  • B. N7k1-Core(config)# iP access-list ARP-FilterNk1-Core(config-acl) # 1 permit ip 10.10.10.1 0.0.0.0 any
  • C. N7k1-Core(config)# IP access-list ARP-FilterNk1-Core(config-mac-acl) # 1 permit iP 10.10.10.1 0.0.0.0. mac 5031. 3ca2. 1bb3 0000.0000.0000
  • D. N7k1-Core(config)# access-list 1 permit 10.10.10.1 0.0.0.0Nk1-Core(config-mac-acl) # 1 permit mac 5031. 3ca2.1bb3 0000.0000 any

Answer: C

NEW QUESTION 13
What can prevent you from adding an interface to a pre-existing port-channel on a CISCO Nexus N7K device?

  • A. The port-channel is In LACP passive mode
  • B. The interface already assigned to a different port-channel,
  • C. The interface has been allocated to a different VOC
  • D. no shutdown was issued on the interface.

Answer: B

NEW QUESTION 14
On the secondary vPC switch, under which circumstance does the vPC autorecovery feature not bring up the vPC member ports?

  • A. Peer link fails, and subsequently, the peer-keepalive link fails.
  • B. Peer link is up, and the peer-keepalive link fails.
  • C. Both vPC peers are reloaded, and the primary does not come back up.
  • D. Peer link fails, and subsequently, the primary switch fails.

Answer: B

NEW QUESTION 15
Refer to the exhibit.
300-180 dumps exhibit
The VEMs fail to join a Cisco Nexus 1000V Series Switch. You determine that a system VLAN must be set on a system-uplink port profile. Which VLAN do you configure as a system VLAN?

  • A. 40
  • B. 10
  • C. 20
  • D. 30

Answer: B

NEW QUESTION 16
Refer to the exhibit.
300-180 dumps exhibit
Which statement about the topology is true?

  • A. Traffic to and from LAN clients is sent through the master router only.
  • B. Clients 1, Client 2, and Client 3 are configured to have the default gateway IP address of 10.0.0.1.
  • C. If Router A fails, the highest interface IP address backup router becomes the master.
  • D. Multiple VRRP groups are configured on each router.

Answer: A

NEW QUESTION 17
Refer to the exhibit.
300-180 dumps exhibit
Which of these is an extension of the virtual machine abstraction that is applied to physical servers?

  • A. service profile
  • B. compute profile
  • C. organization profile
  • D. locale profile
  • E. role profile

Answer: A

NEW QUESTION 18
Which three commands will show all the MAC addresses learned from remote sites in an OTV overlay? (Choose three.)

  • A. show otv arp-nd-cache
  • B. show otv route overlay
  • C. show otv vlan
  • D. show ip arp
  • E. show mac address-table
  • F. show otv site

Answer: ABE

NEW QUESTION 19
Refer to the exhibit.
300-180 dumps exhibit
The server port connected to the NPV edge switch does not come online. Which action should fix the problem?

  • A. Move the NP ports on the NPV edge and the F ports on the NPIV into the same VSAN 99.
  • B. Move the NP ports on the NPV edge and the F ports on the NPIV in the default VSAN 1.
  • C. Move all the ports into VLAN 1.
  • D. Move all the ports into VSAN 99.
  • E. Move all the ports into VLAN 99.

Answer: A

NEW QUESTION 20
You configure two external Layer 3 networks on the same node by using BGP. The network fails to establish BGP adjacencies. Which action do you take to resolve the issue?

  • A. Explicitly define the loopback addresses on the node
  • B. Use OSPF to create a peer that uses external networks
  • C. Configure the router ID to use the interface IP address used to establish the BGP connection
  • D. Configure the router ID to use the loopback interface

Answer: A

Explanation: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/1-x/basic-config/b_ACI_Config_Guide/b

P.S. Easily pass 300-180 Exam with 236 Q&As Passcertsure Dumps & pdf Version, Welcome to Download the Newest Passcertsure 300-180 Dumps: https://www.passcertsure.com/300-180-test/ (236 New Questions)