Want to know Actualtests ccie 400 101 dumps Exam practice test features? Want to lear more about Cisco CCIE Routing and Switching (v5.0) certification experience? Study 100% Guarantee Cisco 400 101 dumps answers to Down to date ccie 400 101 questions at Actualtests. Gat a success with an absolute guarantee to pass Cisco 400 101 pdf (CCIE Routing and Switching (v5.0)) test on your first attempt.
Q471. Which IPv6 tunneling type establishes a permanent link between IPv6 domains over IPv4?
A. IPv4-compatible tunneling
B. ISATAP tunneling
C. 6to4 tunneling
D. manual tunneling
Answer: D
Explanation:
A manually configured tunnel is equivalent to a permanent link between two IPv6 domains over an IPv4 backbone. The primary use is for stable connections that require regular secure communication between two edge routers or between an end system and an edge router, or for connection to remote IPv6 networks.
Reference: http://www.cisco.com/c/en/us/td/docs/ios/ipv6/configuration/guide/12_4t/ipv6_12_4t_book/i p6-tunnel.html
Q472. Refer to the exhibit.
Which statement is true?
A. BGP peer 10.1.2.3 is performing inbound filtering.
B. BGP peer 10.1.2.3 is a route reflector.
C. R1 is a route reflector, but BGP peer 10.1.2.3 is not a route reflector client.
D. R1 still needs to send an update to the BGP peer 10.1.2.3.
Answer: D
Explanation:
On R1 the routing table version (Tbl Ver) for 10.1.2.3 is 1, other routers have version 2, so it needs to send an update to the 10.1.2.3 peer.
Q473. Which two statements about IPsec VTI implementation are true? (Choose two.)
A. The IKE SA can be bound to the VTI and the crypto map.
B. The transform set can be configured only in tunnel mode.
C. SVTIs support only a single IPsec SA.
D. SVTIs support IPv4 packets that carry IPv6 packets.
Answer: B,C
Q474. Which neighbor-discovery message type is used to verify connectivity to a neighbor when the link-layer address of the neighbor is known?
A. neighbor solicitation
B. neighbor advertisement
C. router advertisement
D. router solicitation
Answer: A
Explanation:
IPv6 Neighbor Solicitation Message A value of 135 in the Type field of the ICMP packet header identifies a neighbor solicitation message. Neighbor solicitation messages are sent on the local link when a node wants to determine the link-layer address of another node on the same local link (see the figure below). When a node wants to determine the link-layer address of another node, the source address in a neighbor solicitation message is the IPv6 address of the node sending the neighbor solicitation message. The destination address in the neighbor solicitation message is the solicited-node multicast address that corresponds to the IPv6 address of the destination node. The neighbor solicitation message also includes the link-layer address of the source node.
Figure 1. IPv6 Neighbor Discovery: Neighbor Solicitation Message
Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6_basic/configuration/xe-3s/ip6b-xe-3s-book/ip6-neighb-disc-xe.html
Q475. Which statement describes the effect of the configuration line redistribute maximum-prefix 1500 90 withdraw?
A. After the 1500th route is redistributed, a warning is posted in the log file and 90 more routes are redistributed before further routes are discarded.
B. After the 1350th route is redistributed, a warning is posted in the log file until the 1500th route is redistributed, and then further routes are discarded.
C. After the 1500th route is redistributed, further routes are discarded only if the CPU is above 90%.
D. The routing protocol receives 1500 routes. After the routing process has redistributed 90% of the routes, the process supernets routes and injects a NULL route to prevent black-hole routing.
Answer: B
Q476. What is a reason to use DHCPv6 on a network that uses SLAAC?
A. To get a record of the IPs that are used by the clients
B. To push DNS and other information to the clients
C. No reason, because there is no need for DHCPv6 when using SLAAC
D. Because DHCPv6 can be used only in stateful mode with SLAAC to record the IPs of the clients
E. Because DHCPv6 can be used only in stateless mode with SLAAC to record the IPs of the clients
F. Because DHCPv6 is required to use first-hop security features on the switches
Answer: B
Explanation:
SLAAC is by far the easiest way to configure IPv6 addresses, simply because you don’t have to configure any IPv6 address. With SLAAC, a host uses the IPv6 Neighbor Discovery Protocol (NDP) to determine its IP address and default routers. Using SLAAC, a host requests and listens for Router Advertisements (RA) messages, and then taking the prefix that is advertised to form a unique address that can be used on the network. For this to work, the prefix that is advertised must advertise a prefix length of 64 bits (i.e., /64). But the most significant of Stateless Address Autoconfiguration (SLAAC) is it provided no mechanism for configuring DNS resolver information.Therefore SLACC can be used along with DHCPv6 (Stateless) to push DNS and other information to the clients.
Q477. Which command sets the maximum segment size for a TCP packet initiated from a router?
A. ip mtu
B. ip tcp adjust-mss
C. ip tcp mss
D. ip tcp window-size
Answer: C
Q478. Refer to the exhibit.
All switches have default bridge priorities, and originate BPDUs with MAC addresses as indicated. The numbers shown are STP link metrics. Which two ports are in blocking state after STP converges? (Choose two.)
A. the port on switch SWD that connects to switch SWE
B. the port on switch SWF that connects to switch SWG
C. the port on switch SWD that connects to switch SWC
D. the port on switch SWB that connects to switch SWD
Answer: C,D
Explanation:
This is a scenario that wants you to demonstrate understanding of the Root switch and Root port election process. So, it’s best to start with where the root switch will be and work down from there. It’s setup nicely because the lowest MAC address switch starts at the top and then the lower priority/higher mac addresses move down the architecture. SWA wins the root election and of course all ports in SWA are forwarding. SWB introduces the possibility for a switching loop so it’s important to understand which ports will be put into the blocking state. Since SWD is a higher MAC address it will end up with a blocked port connected to SWB to prevent a loop: and this is one of the correct answers. To prevent the possibility of another potential switching loop, SWD again ends up with the higher MAC address so blocking the link between D and C prevents a B/C/D switching loop.
Q479. Which two types of traffic are blocked when the storm control threshold for multicast traffic is reached on a port? (Choose two.)
A. BPDU
B. OSPF
C. CDP
D. IS-IS
E. LLDP
Answer: B,D
Q480. DRAG DROP
Drag and drop the BGP attribute on the left to the correct category on the right.
Answer: