It is impossible to pass Alcatel-Lucent 4A0-M01 exam without any help in the short term. Come to Examcollection soon and find the most advanced, correct and guaranteed Alcatel-Lucent 4A0-M01 practice questions. You will get a surprising result by our Up to date Alcatel-Lucent IP/MPLS Mobile Backhaul Transport practice guides.

Q17. Click on the exhibit Given the diagram shown, and the following information: 

. Configured on CSA1 is a redundant ePipe service 

. A Multichassis-Link Aggregation Group (MC-LAG) protects the CE access links 

. The preferred spoke SDP has failed After the failure, which status will the MLS2 router signal to CSA 1 on its return spoke SDP 2:1? 

A. Pseudowire forwarding, 0x00 

B. Remote pseudowire active, remote SAP is down, 0x06 

C. Pseudowire forwarding standby,0x20 

D. Remote pseudowirein standby, remote SAP is down,0x26 

Answer:


Q18. A network element (NE) forwards external traffic through a Virtual Routing and 

Redundancy Protocol (VRRP) protected gateway interface. If the master goes offline, how does the NE learn to forward traffic to the new master interface? 

A. Upon assuming the master role, the new master advertises its presence through Gratuitous Address Resolution Protocol (ARP) messages 

B. The master updates the forwarding table entries by delivering all frames into the network using the virtual Media Access Control (MAC) source address 

C. The network elements use their current gateway interface ARP cache entry or send out an ARP request if the entry is timed out 

D. The new master interface delivers the new virtual interface MAC address into the network via Master Advertisement Messages 

Answer:


Q19. Click on the exhibit Given the show result shown, and the following information: 

. A switched ePipe Virtual  Private  Wire  Service  (VPWS)  transits  the Switching Provider Edge (S- PE) router POC3-1 What condition might  cause the spoke Service  Distribution Point  (SDP)  1 status shown? 

A. The SDP 1 Virtual Circuit (VC-ID) doesn't match that configured on peer 192.0.22 

B. The peer 192.0 2.2 service Maximum Transmission Unit (MTU) is set too 

C. The peer 192.0.2.2 Targeted Label Distribution Protocol (T-LDP) session is down 

D. The two S-PE spoke SDP VC-IDs must match 

Answer:


Q20. In a Mobile Service Provider (MSP) network, which device aggregates traffic for delivery to the control elements? 

A. BTP Aggregation Gateway (BG) 

B. BTP Termination Device (BT) 

C. MSP Aggregation Gateway (MG) 

D. MSP Termination Device (MT) 

Answer:


Q21. As cells enter an aPipe service configured for vc-type atm-vcc, how does the ingress Provider Edge  (PE) router handle the cell  header Virtual  Path Identifier/Virtual Channel Identifier (VPI/VCI) values? 

A. The PE strips the cell headers and transports just the payload with a control word 

B. The PE replaces the VPI/VCI with the MPLS service label and control word 

C. The PE replaces the VPI/VCI with another set defined within the service context 

D. The PE transports the original VPI/VCI along with the payload to the egress PE 

Answer:


Q22. A Synchronization Ethernet (SyncE)/Synchronization Status Message (SSM)-capable node is configured to support the ITU-T G.781 SONET mode. Which SSM code indicates that the node has gone into holdover? 

A. QL-DUS 

B. QL-EEC2 

C. QL-STU 

D. QL-PRS 

Answer:


Q23. Which statement is correct concerning spoke SDP use in point-to-point services? 

A. Each service requires its own set of SDPs 

B. The spoke SDP must specify the vc-type of the service transported 

C. SDP bindings must include the service encapsulation type value 

D. An explicit endpoint may have up to four spoke SDP bindings E. Each service includes two default explicit endpoints 

Answer:


Q24. Given the configuration example shown: 

The DS1 port shown will become a Structure Agnostic TDM over Packet (SAToP) 

Service Access Point (SAP) access port. What must be configured on the DS1 port to allow it to carry all 24 TDM timeslots as a stream of consecutive octets? 

A. Set encap-cem in the channel group 

B. Set encap-type satop-t1 on the port 

C. Setframingds1-unframedontheport 

D. Setthe channel-group timeslots to 1-24 

Answer: