Proper study guides for Most recent Cisco Supporting Cisco routing and Switching Network Devices certified begins with Cisco 640-692 preparation products which designed to deliver the High value 640-692 questions by making you pass the 640-692 test at your first time. Try the free 640-692 demo right now.
Online 640-692 free questions and answers of New Version:
NEW QUESTION 1
Refer to the exhibit.
Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure? (Choose two.)
- A. The cable that is connected to S0/0 on RouterA is faulty.
- B. Interface S0/0 on RouterB is administratively down.
- C. Interface S0/0 on RouterA is configured with an incorrect subnet mask.
- D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.
- E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.
- F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.
Answer: EF
NEW QUESTION 2
How does a Cisco switch respond if you boot it without a valid configuration in the NVRAM?
- A. it enters setup mode.
- B. it uses the running –configuration
- C. It prompts you to restore the startup configuration
- D. it enters user EXEC mode.
Answer: B
NEW QUESTION 3
Which command initiates the transfer of a Cisco IOS image over IP from ROMMON?
- A. copy tftp: flash:
- B. copy flash: tftp:
- C. tftpdnld
- D. xmodem
Answer: C
NEW QUESTION 4
The pins and RJ-45 are numbered from 1 through 8. With the material points of the plug facing toward you, pin 1 is the leftmost pin. Which two sets are looped on an RJ-45 T1 loopback plug? (Choose two)
- A. Pins 1 and 4
- B. Pins 1 and 7
- C. Pins 2 and 5
- D. Pins 2 and 8
- E. Pins 1 and 5
- F. Pins 2 and 7
Answer: AC
NEW QUESTION 5
DRAG DROP
Solution:
Step 1 – Power on Step 2 – Mode button Step 3 – flash_init Step 4 – load_helper
Does this meet the goal?
- A. Yes
- B. Not Mastered
Answer: A
NEW QUESTION 6
Refer to the exhibit.
What is the result of setting the no login command?
- A. Telnet access is denied.
- B. Telnet access requires a new password at the first login.
- C. Telnet access requires a new password.
- D. no password is required for telnet access.
Answer: D
NEW QUESTION 7
Which of the following describes the roles of devices in a WAN? (Choose three.)
- A. A CSU/DSU terminates a digital local loop.
- B. A modem terminates a digital local loop.
- C. A CSU/DSU terminates an analog local loop.
- D. A modem terminates an analog local loop.
- E. A router is commonly considered a DTE device.
- F. A router is commonly considered a DCE device.
Answer: ADE
NEW QUESTION 8
From a Windows command prompt, which command displays the local IP address of a computer?
- A. ip config
- B. ip configuration
- C. ipconfig
- D. ipconfiguration
Answer: C
NEW QUESTION 9
Which port displays the bootup process on a Cisco device?
- A. ATM
- B. BVI
- C. Console
- D. Ethernet
Answer: C
NEW QUESTION 10
When using a modem to provide out-of-band access to a Cisco router, which cable type is used to connect the wall jack to the modem?
- A. DB-25 to RJ-11
- B. RJ-11 to Rj-11
- C. RJ-45 to RJ-45
- D. RJ-11 to RJ-45
- E. RJ-11 to DB-9
Answer: B
NEW QUESTION 11
Refer to the exhibit.
Which type of cable us used on the ATM card?
- A. Fiber-optic BNC
- B. Coaxial
- C. Serial
- D. Crossover
Answer: B
NEW QUESTION 12
Which two of the following statements are true? (Choose two)
- A. Because FTP usually requires authentication, a Cisco router must be configured with the appropriate username and password.
- B. FTP uses UDP as its transport protocol.
- C. The copy running-config ftp: command is used to copy a configuration file from an FTP server to the running configuration.
- D. A router can act as an FTP server.
- E. FTP can be used to load Cisco IOS software to router in ROMMON mode.
Answer: AD
NEW QUESTION 13
Which two commands are used to set the configuration register value? (Choose two)
- A. Router(config)#config-register 0x2102
- B. Router(config)#confreg 0x2102
- C. rommon>config-register 0x2102
- D. rommon>confreg 0x2102
- E. Router(config)#configuration-register 0x2102
Answer: AD
NEW QUESTION 14
Which of the following statements are true?
- A. OEM products that are built for Cisco never get a Cisco logo applied.
- B. The Cisco logo, old or new, can be found on the front bezel of all Cisco rack-mountable or desktop products.
- C. Serial numbers are attached by label on all Cisco field-replaceable parts.
- D. At the network level, the user serial number should be different as the part number.
Answer: B
NEW QUESTION 15
What one of the feature is associated with single-mode fiber-optic cable?
- A. a single strand of glass fiber
- B. stored less bandwidth
- C. cost is less than multimode fiber
- D. operates over less distance than multimode fiber
Answer: A
NEW QUESTION 16
While performing password recovery on a Cisco device, the configuration register should be which value in order to bypass loading the startup configuration?
- A. 0x2102
- B. 0x2112
- C. 0x2122
- D. 0x2142
Answer: D
NEW QUESTION 17
The colored wires at one end of the cable in the reverse sequence of the colored wires at the other end of the cable. Which cable does this describe?
- A. Rolled
- B. Coaxial
- C. Crossover
- D. Straight-through
Answer: A
NEW QUESTION 18
Which IOS layer does a server use to keep track of which application communications in which conversation?
- A. Transport
- B. Network
- C. Session
- D. Application
Answer: C
NEW QUESTION 19
Which type of memory is necessary for a router to boot?
- A. DRAM
- B. PVDM
- C. NVRAM
- D. VRAM
Answer: A
NEW QUESTION 20
Which two commands display the saved configuration file? (Choose two)
- A. show configuration
- B. show file system
- C. show running-config
- D. show startup-config
Answer: AD
NEW QUESTION 21
......
Recommend!! Get the Full 640-692 dumps in VCE and PDF From 2passeasy, Welcome to Download: https://www.2passeasy.com/dumps/640-692/ (New 67 Q&As Version)