Latest Delta - HPE Compute Solutions HPE0-S60 Actual Exam

NEW QUESTION 1
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They plan to use Distributed Switches and DRS cluster
You are preparing a proposal with the following components:
- HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
- two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
- an appropriate number of the vSphere Standard licenses for each compute node
- one HPE D3940 Storage Modules with 40 SSDs - all required cables and options Which statement about this proposal is true?

• A. One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50GD/S ILM
• B. vSphere Standard licenses should be replaced with Enterprise Pius licenses to enable requested features
• C. 2 additional HPE Synergy 480 Gen10 Plus compute modules can be added to this setup
• D. 20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drive.

Answer: B

NEW QUESTION 2
Which statement about a new HPE SimpliVity deployment is true?

• A. New HPE SimpliVity deployments gives customer flexible choice of hypervisor
• B. A new HPE SimpliVity node can be a member of multiple dusters
• C. AM new HPE SimpliVity models are software optimized
• D. All new HPE SimpliVity models are based on mid CPUs

Answer: C

NEW QUESTION 3
As a result of the troubleshooting process, you recommend replacing, HPE Synergy Composer modules which HPE Synergy Composer 2
Why would you recommend this change?

• A. HPE Composer 1 running HPE OneView 5 2 or later can support only 12 frames within a single management nog
• B. HPE Composer 2 can support more than the maximum 21 frames that are supported with HPE Composer 1 and HPE OneView.
• C. HPE Composer 2 provides access to 105 interface that can be used for full management of HPE Composer 2 remotely
• D. HPE Composer 1 cannot support remote frames, which doubles the configuration and management procedures effort

Answer: B

NEW QUESTION 4
Which statement about the HPE D3940 storage module is true?

• A. SATA drives requires redundant 10 adapters to be installed in this module
• B. Up to five modules can be installed in a single frame with Gen10 servers
• C. it is configured through CLl available from HPE Synergy console
• D. Only one type of drives (SATA, SAS, SSD) can be installed in each module

Answer: C

NEW QUESTION 5
You are troubleshooting an HPE OneView server profile that presents a critical state. The server profile was configured with a Link Aggregation Group
What should you check to fix the issue?

• A. if both FiexNICs are configured with the same speed
• B. If the logical enclosure is built on at least three HPE Synergy frames
• C. if both FiexNICs are connected to different networks
• D. if the logical enclosure is configured with redundant master modules

Answer: A

NEW QUESTION 6
Your customer plans to deploy HPE OneView for VMware vCenter Server together with HPE Storage Integration Pack for VMware vCenter. The customer wants to use them to manage HPE Synergy Gen10 compute modules. HPE ProLiant Gen 10 servers and an MSA array.
Which statement about compatibility of the existing environment with the planned software components is true?

• A. Both HPE Synergy Gen10 full-height compute module plugins will require a license
• B. HPE OneView for VMware vCenter Server does not support standalone HPE ProLiant servers
• C. To use the required plugins HPE ProLiant Gen10 systems must be managed using HPE OneView
• D. HPE Storage integration Pack for VMware vCenter does not support MSA arrays

Answer: B

NEW QUESTION 7
Which statement about HPE Superdome nPars is true?

• A. Chassis in the same nPar can have different CPU configuration
• B. Rack Management Controller is required Tor nPar configuration
• C. Chassis in the same nPar can have different memory configuration
• D. nPars are supported only with 3rd Generation Intel Xeon Scalable Processors

Answer: C

NEW QUESTION 8
Which statement about the SY480 Gen10 Plus Compute Module is true?

• A. It cannot be mixed with Gen9 compute modules in the same frame.
• B. It supports 8 memory channels and memory DIMMs of up to 256GB.
• C. It only supports NVDIMM Persistent Memory.
• D. It supports "3rd Gen AMO EPYC Server Processors with 64 cores.

Answer: C

NEW QUESTION 9
Click the drop-down menu that will allow you to define the location of the master modules within the logical interconnect group.

• A. Yes
• B. Not Mastered

Answer: A

NEW QUESTION 10
Your customer is implementing an HPE Synergy solution based on three frames. Click each of the ports that can be used to connect satellite modules.

• A. Yes
• B. Not Mastered

Answer: A

NEW QUESTION 11
Your customer plans to deploy ESXi systems to HPE Synergy and HPE ProLiant servers using HPE OneView for VMware vCenter Server.
Which statement about HPE OneView for VMware vCenter Server functionality is true for this environment?

• A. HPE ProLiant servers need an HPE OneView for VMware vCenter Server license for full functionality
• B. Individual systems can be added to HPE OneView for VMware vCenter Server through an ILO management processor
• C. HPE Synergy requires HPE Composer 2 for full functionality of HPE OneView for VMware vCenter Server
• D. Only systems managed using HPE Oneview can use HPE Oneview for VMware vCenter Server functionalities

Answer: A

NEW QUESTION 12
Your customer wants to add a second HPE Synergy frame to an existing logical enclosure Based on a single HPE Synergy frame. The customer wants to use a highly available master setup.
Which procedures should De performed during the expansion process? (Select two.)

• A. Create a new logical interconnect group and enclosure group for two frames setup
• B. Create a new logical enclosure based on both HPE Synergy frames.
• C. Re-parent an existing enclosure group to the new logical interconnect group.
• D. Modify an existing logical interconnect to include second HPE Synergy frame.
• E. Move one of the master modules to the appropriate interconnect bay in the second frame.

Answer: BD

NEW QUESTION 13
Your customer has experience with utilization sampling for HPE Virtual Connect SE 100 Gb F32 Module for HPE Synergy. They have recently purchased HPE VC FC modules.
What must you be aware of regarding utilization sampling for the new modules?

• A. Utilization sampling for HPE VC FC modules must be enabled manually using CLI.
• B. For HPE VC FC modules, utilization sampling is always enabled and cannot be disabled
• C. For HPE VC FC modules, utilization sampling can be enabled once appropriate license is applied
• D. Utilization sampling works the same way tor any type of HPE Synergy interconnect modules

Answer: D

NEW QUESTION 14
Match each HPE Synergy logical component with the definition.

• A. Yes
• B. Not Mastered

Answer: A

NEW QUESTION 15
Match HPE SimpliVity term with the definition.

• A. Yes
• B. Not Mastered

Answer: A

NEW QUESTION 16
Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex 280 They plan to manage new components using HPE OneView
What must be done to achieve this goal?

• A. The customer must use IL05 to add HPE Superdome Flex systems to HPE OneView
• B. The customer should deploy an HPE OneView appliance for HPE Superdome Flex management
• C. The customer must add a second Rack Management Controller for HPE Superdome Flex 280
• D. The customer has to add HPE Superdome Flex to the HPE OneView used to manage HPE Synergy

Answer: C

NEW QUESTION 17
......