Our pass rate is high to 98.9% and the similarity percentage between our nse7 exam study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Fortinet fortinet nse7 exam in just one try? I am currently studying for the Fortinet nse7 exam exam. Latest Fortinet nse7 fortinet Test exam practice questions and answers, Try Fortinet nse7 fortinet Brain Dumps First.

Q9. An administrator has enabled HA session synchronization in a HA cluster with two members. Which flag is added to a primary unit's session to indicate that it has been synchronized to the secondary unit? 

A. redir 

B. dirty 

C. synced 

D. nds 

Answer: C 


Q10. Examine the following routing table and BGP configuration; then answer the question below. 

TheBGP connection is up, but the local peer is NOT advertisingthe prefix 192.168.1.0/24. Which configuration change will make the local peer advertise this prefix? 

A. Enable the redistribution of connected routers into BGP. 

B. Enable the redistribution of static routers into BGP. 

C. Disable the setting network-import-check. 

D. Enable the setting ebgp-multipath. 

Answer: C 


Q11. Examine the output from the 'diagnose debug authd fsso list' command; then answer the question below. 

# diagnose debug authd fsso list—FSSO logons-IP: 192.168.3.1 User: STUDENT Groups:TRAININGAD/USERS Workstation: INTERNAL2. TRAINING. LAB The IP address 192.168.3.1 is NOT the one used by the workstation INTERNAL2. TRAINING. LAB. 

What should the administrator check? 

A. The IP address recorded in the logon event for the user STUDENT. 

B. The DNS name resolution for the workstation name INTERNAL2. TRAINING. LAB. 

C. The source IP address of the traffic arriving to the FortiGate from the workstation INTERNAL2. TRAINING. LAB. 

D. The reserve DNS lookup forthe IP address 192.168.3.1. 

Answer: C 


Q12. An LDAP user cannot authenticate against a FortiGate device. Examine the real time debug output shown in the exhibit when the user attempted the authentication; then answer thequestion below. 

Based on the output in the exhibit, what can cause this authentication problem? 

A. User student is not found in the LDAP server. 

B. User student is using a wrong password. 

C. The FortiGate has been configured with the wrongpassword for the LDAP administrator. 

D. The FortiGate has been configured with the wrong authentication schema. 

Answer: A 


Q13. Examine the following partial output from two system debug commands; then answer the question below. 

Which of the following statements are true regarding the aboveoutputs? (Choose two.) 

A. The unit is running a 32-bit FortiOS 

B. The unit is in kernel conserve mode 

C. The Cached value is always the Active value plus the Inactive value 

D. Kernel indirectly accesses the low memory (LowTotal) through memory paging 

Answer: A,C 


Q14. When does a RADIUS server send anAccess-Challengepacket? 

A. The server does not have the user credentials yet. 

B. The server requires more information from the user,such as the token code for two-factor authentication. 

C. The user credentials are wrong. 

D. The user account is not found in the server. 

Answer: B 


Q15. Examine the following partial outputs from two routing debug commands; then answer the question below. 

# get router info routing-table database 

s 0.0.0.0/0 [20/0] via 10.200.2.254, port2, [10/0] s *> 0.0.0.0/0 [10/0] via 10.200.1.254, port1 

# get router info routing-table all 

s* 0.0.0.0/0 [10/0] via 10.200.1.254, port1 

Why the default route using port2 is not displayed in the output of the second command? 

A. it has a lower priority than the default route using port1. 

B. it has a higher priority than the default route using portl. 

C. it has a higher distance than the default route using portl. 

D. it is disabled in the FortiGate configuration. 

Answer: A 


Q16. Examine the following partial outputs from two routing debug commands; then answer the question below. 

# get router info routing-table database 

s 0.0.0.0/0 [20/0] via 10.200.2.254, port2, [10/0] s *> 0.0.0.0/0 [10/0] via 10.200.1.254, port1 

# get router info routing-table all 

s* 0.0.0.0/0 [10/0] via 10.200.1.254, port1 

Why the default route using port2 is not displayed in the output of the second command? 

A. it has a lower priority than the default route using port1. 

B. it has a higher priority than the default route using portl. 

C. it has a higher distance than the default route using portl. 

D. it is disabled in the FortiGate configuration. 

Answer: A