Your success in Fortinet nse7 exam is our sole target and we develop all our nse7 fortinet braindumps in a way that facilitates the attainment of this target. Not only is our fortinet nse7 study material the best you can find, it is also the most detailed and the most updated. nse7 exam Practice Exams for Fortinet fortinet nse7 are written to the highest standards of technical accuracy.
Q1. When does a RADIUS server send anAccess-Challengepacket?
A. The server does not have the user credentials yet.
B. The server requires more information from the user,such as the token code for two-factor authentication.
C. The user credentials are wrong.
D. The user account is not found in the server.
Answer: B
Q2. A FortiGate device has the following LDAP configuration:
Based on the output, what FortiGate LDAP setting is configured incorrectly?
A. cnid.
B. username.
C. password.
D. dn.
Answer: B
Q3. An administrator has enabled HA session synchronization in a HA cluster with two members. Which flag is added to a primary unit's session to indicate that it has been synchronized to the secondary unit?
A. redir
B. dirty
C. synced
D. nds
Answer: C
Q4. Examine the IPsec configuration shown in the exhibit; then answer the question below.
An administrator wants to monitor the VPN byenable the IKE real time debug using these commands:
diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable
The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output?
A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up.
B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter.
C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1
D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally.
Answer: A
Q5. An administrator has decreased all the TCP session timers to optimize the FortiGate memory usage. However, after thechanges, one network application started to have problems. During the troubleshooting, the administrator noticed that the FortiGate deletes the sessions after the clients send the SYN packets and before the arrival of the SYN/ACKs. When the SYN/ACK packetsarrive to the FortiGate, the unit has already deleted the respective sessions. Which TCP session timer must be increased to fix this problem?
A. TCP half open.
B. TCP half close.
C. TCP time wait.
D. TCP session time to live.
Answer: D
Q6. What configuration changes can reduce the memory utilization in a FortiGate? (Choose two.)
A. Reduce the session time to live.
B. Increase the TCP session timers.
C. Increase the FortiGuard cache time to live.
D. Reduce the maximum file size to inspect.
Answer: A,D
Q7. Examine the IPsec configuration shown in the exhibit; then answer the question below.
An administrator wants to monitor the VPN byenable the IKE real time debug using these commands:
diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable
The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output?
A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up.
B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter.
C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1
D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally.
Answer: A
Q8. When does a RADIUS server send anAccess-Challengepacket?
A. The server does not have the user credentials yet.
B. The server requires more information from the user,such as the token code for two-factor authentication.
C. The user credentials are wrong.
D. The user account is not found in the server.
Answer: B