It is impossible to pass Cisco 200 125 ccna v3 0 exam without any help in the short term. Come to Examcollection soon and find the most advanced, correct and guaranteed Cisco cisco ccna 200 125 practice questions. You will get a surprising result by our Up to date CCNA Cisco Certified Network Associate CCNA (v3.0) practice guides.
P.S. Virtual 200-125 questions are available on Google Drive, GET MORE: https://drive.google.com/open?id=1G0OQvn58oVaFHU8QUjdLariF4zPSu0BB
New Cisco 200-125 Exam Dumps Collection (Question 7 - Question 16)
New Questions 7
Which NTP command configures the local device as an NTP reference clock source?
A. ntp peer
B. ntp broadcast
C. ntp master
D. ntp server
Answer: D
New Questions 8
Which three circumstances can cause a GRE tunnel to be in an up/down state for site id:28254851? (Choose three.)
A. The tunnel interface IP address is misconfigured.
B. The tunnel interface is down.
C. A valid route to the destination address is missing from the routing table.
D. The tunnel address is routed through the tunnel itself.
E. The ISP is blocking the traffic.
F. An ACL is blocking the outbound traffic.
Answer: B,C,D
New Questions 9
Which statement about Cisco Discovery Protocol is true?
A. It is a Cisco-proprietary protocol.
B. It runs on the network layer.
C. It can discover information from routers, firewalls, and switches.
D. It runs on the physical layer and the data link layer.
Answer: A
New Questions 10
What is the best way to verify that a host has a path to other hosts in different networks?
A. Ping the loopback address.
B. Ping the default gateway.
C. Ping the local interface address.
D. Ping the remote network.
Answer: D
Explanation:
Ping is a tool that helps to verify IP-level connectivity; PathPing is a tool that detects packet loss over multiple-hop trips. When troubleshooting, thepingcommand is used to send an ICMP Echo Request to a target host name or IP address. Use Ping whenever you want to verify that a host computer can send IP packets to a destination host. You can also use the Ping tool to isolate network hardware problems and incompatible configurations.
If you callipconfig /alland receive a response, there is no need to ping the loopback address and your own IP address u2014 Ipconfig has already done so in order to generate the report.
It is best to verify that a route exists between the local computer and a network host by first using ping and the IP address of the network host to which you want to connect. The command syntax is:
ping <IP address>
Perform the following steps when using Ping:
u2711 Ping the loopback address to verify that TCP/IP is installed and configured correctly on the local computer.
ping 127.0.0.1
If the loopback step fails, the IP stack is not responding. This might be because the TCP drivers are corrupted, the network adapter might not be working, or another service is interfering with IP.
u2711 Ping the IP address of the local computer to verify that it was added to the network
correctly. Note that if the routing table is correct, this simply forwards the packet to the loopback address of 127.0.0.1.
ping<IP address of local host>
u2711 Ping the IP address of the default gateway to verify that the default gateway is functioning and that you can communicate with a local host on the local network.
ping<IP address of default gateway>
u2711 Ping the IP address of a remote host to verify that you can communicate through a router.
ping<IP address of remote host>
u2711 Ping the host name of a remote host to verify that you can resolve a remote host name.
ping<Host name of remote host>
u2711 Run a PathPing analysis to a remote host to verify that the routers on the way to the destination are operating correctly.
pathping<IP address of remote host>
New Questions 11
What are two reasons that duplex mismatches can be difficult to diagnose? (Choose two.)
A. The interface displays a connected (up/up) state even when the duplex settings are mismatched.
B. The symptoms of a duplex mismatch may be intermittent.
C. Autonegotiation is disabled.
D. Full-duplex interfaces use CSMA/CD logic, so mismatches may be disguised by collisions.
E. 1-Gbps interfaces are full-duplex by default.
Answer: A,B
New Questions 12
Which condition indicates that service password-encryption is enabled?
A. The local username password is encrypted in the configuration.
B. The enable secret is encrypted in the configuration.
C. The local username password is in clear text in the configuration.
D. The enable secret is in clear text in the configuration.
Answer: A
New Questions 13
When enabled, which feature prevents routing protocols from sending hello messages on an interface'?
A. virtual links
B. passive-interface
C. directed neighbors
D. OSPF areas
Answer: B
Explanation:
You can use thepassive-interfacecommand in order to control the advertisement of routing information. The command enables the suppression of routing updates over some interfaces while it allows updates to be exchanged normally over other interfaces.
With most routing protocols, thepassive-interfacecommand restricts outgoing advertisements only. But, when used with Enhanced Interior Gateway Routing Protocol (EIGRP), the effect is slightly different. This document demonstrates that use of the passive-interfacecommand in EIGRP suppresses the exchange of hello packets between two routers, which results in the loss of their neighbor relationship. This stops not only routing updates from being advertised, but it also suppresses incoming routing updates. This document also discusses the configuration required in order to allow the suppression
of outgoing routing updates, while it also allows incoming routing updates to be learned normally from the neighbor.
New Questions 14
What is the correct routing match to reach 172.16.1.5/32?
A. 172.16.1.0/26
B. 172.16.1.0/25
C. 172.16.1.0/24
D. the default route
Answer: A
New Questions 15
You enter the show ipv6 route command on an OSPF device and the device displays a route. Which conclusion can you draw about the environment?
A. OSPF is distributing IPv6 routes to BGP.
B. The router is designated as an ABR.
C. The router is designated as totally stubby.
D. OSPFv3 is in use.
Answer: A
New Questions 16
Which three statements about static routing are true? (Choose three.)
A. It uses consistent route determination.
B. It is best used for small-scale deployments.
C. Routing is disrupted when links fail.
D. It requires more resources than other routing methods.
E. It is best used for large-scale deployments.
F. Routers can use update messages to reroute when links fail.
Answer: A,B,C
Recommend!! Get the Virtual 200-125 dumps in VCE and PDF From Examcollectionplus, Welcome to download: https://www.examcollectionplus.net/vce-200-125/ (New 889 Q&As Version)