Finding a new Cisco Cisco exam practice questions is not a new difficult work; however, finding an traditional and logical Cisco 200-125 check questions which contain precise answers is the one other matter. Testking is configured to be able to supply with the high-quality Cisco Cisco simulated tests. A lot of candidates choose our Cisco training study course which possess real expertise and understanding. You can preview and also review your theoretical knowledge using the combination of the practical Cisco 200-125 check. You can discover our Cisco 200-125 exam questions with a fast rate and check yourself using the trustworthy answers.

2021 Oct 200-125 practice test

Q131. - (Topic 2) 

Refer to the exhibit. 


Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.) 

A. SwitchA, Fa0/2, designated 

B. SwitchA, Fa0/1, root 

C. SwitchB, Gi0/2, root 

D. SwitchB, Gi0/1, designated 

E. SwitchC, Fa0/2, root 

F. SwitchD, Gi0/2, root 

Answer: A,B,F 


Q132. - (Topic 7) 

Refer to the exhibit. 


HostA cannot ping HostB. Assuming routing is properly configured, what is the cause of this problem? 

A. HostA is not on the same subnet as its default gateway. 

B. The address of SwitchA is a subnet address. 

C. The Fa0/0 interface on RouterA is on a subnet that can't be used. 

D. The serial interfaces of the routers are not on the same subnet. 

E. The Fa0/0 interface on RouterB is using a broadcast address. 

Answer: D 


Q133. - (Topic 4) 

Refer to the exhibit. 


For what two reasons has the router loaded its IOS image from the location that is shown? (Choose two.) 

A. Router1 has specific boot system commands that instruct it to load IOS from a TFTP server. 

B. Router1 is acting as a TFTP server for other routers. 

C. Router1 cannot locate a valid IOS image in flash memory. 

D. Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server. 

E. Cisco routers will first attempt to load an image from TFTP for management purposes. 

Answer: A,C 


Q134. - (Topic 2) 

Which command can be used from a PC to verify the connectivity between hosts that connect through a switch in the same LAN? 

A. ping address 

B. tracert address 

C. traceroute address 

D. arp address 

Answer: A 


Q135. CORRECT TEXT - (Topic 7) 

Central Florida Widgets recently installed a new router in their office. Complete the network installation by performing the initial router configurations and configuring R1PV2 routing using the router command line interface (CLI) on the RC. 

Configure the router per the following requirements: 

Name of the router is R2 

Enable. secret password is cisco 

The password to access user EXEC mode using the console is cisco2 

The password to allow telnet access to the router is cisco3 

IPV4 addresses mast be configured as follows: 

Ethernet network 209.165.201.0/27 - router has fourth assignable host address in subnet 

Serial network is 192.0.2.176/28 - router has last assignable host address in the subnet. 

Interfaces should be enabled. 

Router protocol is RIPV2 

Attention: 

In practical examinations, please note the following, the actual information will prevail. 

1. Name or the router is xxx 

2. EnablE. secret password is xxx 

3. Password In access user EXEC mode using the console is xxx 

4. The password to allow telnet access to the router is xxx 

5. IP information 


Answer: Router>enable 

Router#config terminal 

Router(config)#hostname R2 

R2(config)#enable secret Cisco 1 

R2(config)#line console 0 

R2(config-line)#password Cisco 2 

R2(config-line)#exit 

R2(config)#line vty 0 4 

R2(config-line)#password Cisco 3 

R2(config-line)#login 

R2(config-line)#exit 

R2(config)#interface faO/0 

R2(config-if)#ip address 209.165.201.4 255.255.255.224 

R2(config)#interface s0/0/0 

R2(config-if)#ip address 192.0.2.190 255.255.255.240 

R2(config-if)#no shutdown 

R2(config-if)#exit 

R2(config)#router rip 

R2(config-router)#version 2 

R2(config-router)#network 209.165.201.0 

R2(config-router)#network 192.0.2.176 

R2(config-router)#end 

R2#copy run start 


200-125 sample question

Up to date 200-125 exam topics:

Q136. - (Topic 7) 

Refer to the exhibit. 


If the devices produced the given output, what is the cause of the EtherChannel problem? 

A. SW1's Fa0/1 interface is administratively shut down. 

B. There is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces. 

C. There is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces. 

D. There is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces. 

Answer: D 


Q137. - (Topic 8) 

What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command? 

A. defines the destination IP address that is used in all broadcast packets on DCLI 202 

B. defines the source IP address that is used in all broadcast packets on DCLI 202 

C. defines the DLCI on which packets from the 192.168.1.2 IP address are received 

D. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address 

Answer: D 


Q138. - (Topic 7) 

What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance? 

A. SNMP 

B. Netflow 

C. WCCP 

D. IP SLA 

Answer: B 


Q139. - (Topic 5) 

Which two statements about static NAT translations are true? (Choose two.) 

A. They allow connections to be initiated from the outside. 

B. They require no inside or outside interface markings because addresses are statically defined. 

C. They are always present in the NAT table. 

D. They can be configured with access lists, to allow two or more connections to be initiated from the outside. 

Answer: A,C 


Q140. - (Topic 3) 

Which IPv6 address is the equivalent of the IPv4 interface loopback address 127.0.0.1? 

A. ::1 

B. :: 

C. 2000::/3 

D. 0::/10 

Answer: A