Q31. Which two of these support an ad-hoc conference call? (Choose two.)
A. Cisco TelePresence Multiway with Cisco TelePresence Multipoint Control Unit and Cisco TelePresence Video Communications Server
B. using the Cisco TelePresence Management Suite Scheduler to schedule a conference call to start in 5 minutes
C. using the Booking tab in the Cisco TelePresence Management Suite to configure a new conference
D. using the tab Administrative Tools > Configuration > Conference Settings in the Cisco TelePresence Management Suite
E. pressing the conference button on a Cisco Unified IP Phone 8941 to conference in a third call
Answer: A,E
Q32. Which codec is most suitable for a video streaming solution?
A. AAC-LD
B. G.729
C. H.264
D. G.711
Answer: C
Q33. Refer to the exhibit.
Which system tab can be used to add video infrastructure devices and endpoints?
A. Navigator
B. System Overview
C. Configuration Templates
D. Provisioning
E. Administrative Tools
Answer: A
Q34. Which two of these are required in order to complete the password recovery of a Cisco TelePresence System endpoint? (Choose two.)
A. must have FTP enabled on the endpoint
B. must have SSH enabled on the endpoint
C. must have the security question answer for the endpoint
D. must be in the same room as the main display
E. must have SFTP enabled on the endpoint
F. must call Cisco TAC for the security code
Answer: B,D
Q35. You have installed a C-Series endpoint in an office where DHCP is not supported. At a minimum, which four network items must be configured for the endpoint to be able to register with H.323 on a Cisco TelePresence Video Communication Server located at the external headquarters location? (Choose four.)
A. unique IPv4 address
B. subnet mask
C. default gateway
D. Cisco VCS IPv4 address
E. Active Directory IPv4 address
F. SMTP server IPv4 address
Answer: A,B,C,D
Q36. What is the optimum distance for a person sitting using the Cisco TelePresence System 500?
A. the camera can adjust automatically
B. 0.5 meters and 0.75 meters (1.5 and 2.5 feet)
C. 1.2 meters and 1.8 meters (4 and 6 feet)
D. 3.0 and 5.0 meters (10 and 15 feet)
Answer: C
Q37. What is the main difference between a Cisco TelePresence Multipoint Control Unit and a Cisco TelePresence Multipoint Switch?
A. The Cisco TelePresence Multipoint Control Unit is a hardware bridge. The Cisco TelePresence Multipoint Switch is a software bridge.
B. The Cisco TelePresence Multipoint Control Unit is a software bridge for immersive and non-immersive endpoints. The Cisco TelePresence Multipoint Switch is a hardware bridge for non-immersive endpoints.
C. The Cisco TelePresence Multipoint Control Unit delivers automatic voice-activated switching. The Cisco TelePresence Multipoint Switch provides active presence.
D. The Cisco TelePresence Multipoint Control Unit has a latency of less than 10 ms, whereas the Cisco TelePresence Multipoint Switch has a latency of 100 ms.
Answer: A
Q38. Which four features are provided by Cisco TelePresence Management Suite? (Choose four.)
A. Scheduling of video conference calls
B. Built-in-bridge functionality for multiparty video conferences
C. SIP-H.323 protocol interworking
D. Centralized management of conference resources
E. SMTP email event notification
F. Endpoint configuration backup and restore
G. Cisco TelePresence endpoint automated redundancy
H. Automated resource optimization
Answer: A,D,E,F
Q39. An engineer is configuring VIP mode for a Cisco TelePresence Multipoint Switch. What are three characteristics the engineer must keep in mind? (Choose three.)
A. VIP mode can be configured only when the meeting is not active.
B. The VIP is displayed on the center screen for three screen systems.
C. Network multipoint meetings are supported.
D. VIP mode timers must be configured from the CLI.
E. Locking is not supported.
F. Only one VIP can be configured for each meeting.
Answer: B,D,F
Q40. A technician is tasked with performing a room readiness assessment in preparation for an immersive video endpoint. What are three Cisco best practices regarding lighting recommendations for the room? (Choose three.)
A. The bulb temperature should be between 4000 and 4100K.
B. Key lighting should be between 200 and 400 Lux with the endpoint powered on.
C. Shoulder lighting should not exceed two times the facial lighting values with the endpoint off.
D. Use direct lighting fixtures.
E. Within the camera field of view, the lighting for all parts of the room should not fluctuate more than 100 Lux.
F. Avoid using dimming light control systems.
Answer: A,C,E