Master the 210-065 Implementing Cisco Video Network Devices v1.0 content and be ready for exam day success quickly with this Testking 210-065 test preparation. We guarantee it!We make it a reality and give you real 210-065 questions in our Cisco 210-065 braindumps.Latest 100% VALID Cisco 210-065 Exam Questions Dumps at below page. You can use our Cisco 210-065 braindumps and pass your exam.

Q21. Which of these needs to be enabled in Cisco Unified Communications Manager in order for the Cisco TelePresence System 500-32 to be able to share a presentation with a Cisco TelePresence System Codec C40 endpoint that is registered to a VCS? 

A. Allow iX application media 

B. Send send-receive SDP in mid-call invite 

C. Allow presentation sharing using BFCP 

D. Allow presentation sharing using H.235 

E. Deliver conference bridge identifier 

Answer:


Q22. In this item, you will need to use all information presented to you to successfully answer the question. 

Refer to the exhibits. An administrator needs to perform a factory reset on a C-Series endpoint. What are two valid ways to accomplish this task? (Choose two.) 

A. Exhibit A 

B. Exhibit B 

C. Exhibit C 

D. Exhibit D 

E. Exhibit E 

Answer: C,D 


Q23. An engineer is configuring a Cisco TelePresence System endpoint for use with a maximum of six people in the room. Which table type should be configured when setting up cameras where two participants directly face the endpoint display? 

A. short racetrack 

B. long racetrack 

C. short rectangle 

D. long rectangle 

Answer:


Q24. Refer to the exhibit. 

A technician is reviewing the search history details on a Cisco TelePresence VCS for a recent call that failed. What was the cause for the call setup failure? 

A. A local call policy rule denied the call. 

B. The source alias matched an entry in the registration deny list. 

C. The originating caller was not authenticated. 

D. The source alias origin is unknown. 

Answer: A


Q25. Which four features are supported by Cisco TelePresence Server for all hardware models in remotely managed mode? (Choose four.) 

A. auto-attendant 

B. ClearPath 

C. Cluster sizes of more than 5 servers 

D. Cascading 

E. Active presence for all devices 

F. Support for Conductor 

G. Native scheduling capabilities 

Answer: B,D,E,F 


Q26. Which two protocols can be used with the Cisco TelePresence Content Server to allow users to share content from their laptops? (Choose two.) 

A. BFCP 

B. H.239 

C. PCoIP 

D. Switched Presentation 

E. SCCP 

F. RDP 

Answer: A,B 


Q27. A customer wants to record Cisco TelePresence conferences with the ability to alter the video format and add captions. Which two products are recommended to accomplish this goal? (Choose two.) 

A. Show and Share 

B. Digital Media Manager 

C. Interactive Experience Manager 

D. Media Experience Engine 

E. TelePresence Content Server 

Answer: D,E 


Q28. A large company wants to procure video conference devices that allow multipoint conferences from C-Series and immersive endpoints that are registered to a Cisco VCS and Cisco Unified Communications Manager. Which two components meet the requirements of this company? (Choose two.) 

A. Cisco TelePresence Multipoint Switch registered to Cisco VCS 

B. Cisco C-Series endpoint with a multisite option key registered to Cisco VCS 

C. Cisco TelePresence Server registered to Cisco VCS 

D. Cisco C-Series endpoint with a multisite option key registered to Cisco Unified Communications Manager 

E. Cisco TelePresence Multipoint Switch trunked to Cisco Unified Communications Manager 

Answer: C,E 


Q29. What is the importance of defining option 150 in the DHCP server for Cisco TelePresence endpoints? 

A. Option 150 is not important. 

B. It is the TFTP server IPv4 address where the video endpoint retrieves its configuration file while booting. 

C. It is the IPv4 address of the default gateway for the subnet that the video endpoint is connected to. 

D. It is the configured SIP registrar and proxy server. 

E. It is the unique NTP server IPv4 address. 

Answer:


Q30. In this item, you will need to use all information presented to you to successfully answer the question. 

The C-Series endpoint (codec) does not register with the Video Communication Server that is located in a different network. Based on the exhibits, what could be causing the issue? 

A. The subnet mask on the codec is incorrect. 

B. The ip address of the codec is incorrect. 

C. The interface that the codec is in is in the wrong VLAN. 

D. The codec did not receive a DHCP address from the DHCP server. 

Answer:

Explanation: 

The subnet mask configured on the codec is 255.255.255.128, when it should be 

255.255.255.0.