Exambible ccnp 300 101 dumps Questions are updated and all ccnp routing and switching route 300 101 official cert guide answers are verified by experts. Once you have completely prepared with our 300 101 dumps exam prep kits you will be ready for the real 300 101 route exam without a problem. We have Improve Cisco 300 101 route pdf dumps study guide. PASSED examcollection 300 101 First attempt! Here What I Did.
P.S. Printable 300-101 questions are available on Google Drive, GET MORE: https://drive.google.com/open?id=1VVsMJd1T1ylej0aePOIREXo7V31c7pn0
New Cisco 300-101 Exam Dumps Collection (Question 2 - Question 11)
Q1. Which option must be configured on a target device to use time stamping to accurately represent response times using IP SL ?
A. Responder
B. Jitter value
C. TCP Connect
D. ICMP Echo
Answer: D
Q2. Which LSA type can exist only in an OSPF NSSA area?
A. type 7 LSA
B. type 1 LSA
C. type 5 LSA
D. type 3 LSA
Answer: A
Q3. DHCPv6 can obtain configuration parameters from a server through rapid two-way message exchange. Which two steps are involved in this process? (Choose Two)
A. solicit
B. advertise
C. request
D. auth
E. reply
Answer: A,C
Q4. A network engineer applies the command ip tcp adjust-mss <bytes> under interface configuration mode. What is the result?
A. The probability of SYN packet truncation is increased.
B. The UDP session is inversely affected.
C. The probability of dropped or segmented TCP packets is decreased.
D. The optimum MTU value for the interface is set.
Answer: C
Q5. Which statement describes what this command accomplishes when inside and outside interfaces are correctly identified for NAT?
ip nat inside source static tcp 192.168.1.50 80 209.165.201.1 8080 extendable
A. It allows host 192.168.1.50 to access external websites using TCP port 8080.
B. It allows external clients coming from public IP 209.165.201.1 to connect to a web server at 192.168.1.50.
C. It allows external clients to connect to a web server hosted on 192.168.1.50.
D. It represents an incorrect NAT configuration because it uses standard TCP ports.
Answer: C
Q6. Which command sequence can you enter a router to configure Unicast Reverse Path Forwarding in loose mode?
A. interface GigabitEthernet0/0
ip verify unicast source reachable-via loose.
B. interface GigabitEthernet0/0
ip verify unicast source reachable-via all.
C. interface GigabitEthernet0/0
ip verify unicast source reachable-via any.
D. interface GigabitEthernet0/0
ip verify unicast source reachable-via rx.
Answer: C
Q7. Refer to the exhibit.
Which interoperability technique implemented on the router would allow Host-1 to communicate with Host-2?
A. Dual Stack
B. NAT-PT
C. 6to4 tunnel
D. GRE tunnel
E. ISATAP tunnel
Answer: B
Q8. A network engineer enables OSPF on a Frame Relay WAN connection with circuit-id 28468340 to various remote sites, but no OSPF adjacencies come up. Which two actions are possible solutions for this issue? (Choose Two)
A. Change the network type to point-to-multipoint under WAN interface.
B. Enable virtual links.
C. Change the network type to nonbroadcast multipoint access.
D. Configure the neighbor command under OSPF process for each remote site.
E. Ensure that the OSPF process number matches among all remote sites
Answer: A,D
Q9. What is IPv6 router solicitation?
A. a request made by a node to join a specified multicast group
B. a request made by a node for its IP address
C. a request made by a node for the IP address of the DHCP server
D. a request made by a node for the IP address of the local router
Answer: D
Q10. In which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup
D. redundant routers running VRRP
Answer: A
Recommend!! Get the Printable 300-101 dumps in VCE and PDF From Dumpscollection, Welcome to download: http://www.dumpscollection.net/dumps/300-101/ (New 487 Q&As Version)