Cisco 300-175 Exam Questions and Answers 2021

NEW QUESTION 1
Open the windows by clicking on the minimized at the bottom of the viewing area. Windows can be minimized by clicking on the [X], repositioned by dragging the title bar, and resized by using the handle at the lower right corner to customize the viewing area.
If you are required to access the devices to complete this scenario, the mouse cursor will use a hand symbol when moved over device icons. Clicking the icon will open a device terminal so you can interact with the hardware.
Open the Questions window and begin by clicking a question number. When you have completed answering all questions, click Done to continue.
Scenario
Use your UCS knowledge on Adapter errors ………………………………………configurations.

We are working on which Chassis ID?

• A. 1
• B. 2
• C. 3
• D. 4
• E. 5

Answer: A

NEW QUESTION 2
While configuring VM-FEX for Hyper-V, the virtual switch does not show up when you add the host with the port-profile management snap-in. Which statement describes the most likely cause?

• A. SR-IOV is not enabled for the virtual switch inside Hyper-V.
• B. Cisco Nexus 1000v is not enabled for the virtual switch.
• C. Hyper-V requires Cisco UCS Manager to utilize Cisco Discovery Protocol on the vNIC profile.
• D. An active VM is not associated with the port profile.
• E. VM-FEX does not work with Hyper-V.
• F. VM-FEX has been configured on the Catalyst switch but not in System Center yet.

Answer: A

NEW QUESTION 3
Refer to the exhibit.

Which description of the result is true?

• A. An Ethernet monitoring session was created where traffic may be copied and forwarded to slot 1 port 9 for analysis.
• B. An Ethernet monitoring session was created, activated and committed.
• C. Ethernet traffic from slot 9 port 1 will be copied and forwarded to the destination SPAN port for analysis.
• D. Ethernet traffic from slot 1 port 9 will be copied and forwarded to the destination SPAN port for analysis.

Answer: A

NEW QUESTION 4
Refer to the Exhibit:

Refer to the exhibit. Which action do you take to ensure that the IP addresses in IP pool ext-mgmt are selected in a random order?

• A. Select the Default option in the Assignment Order property
• B. Delete all the IP pools except for IP pool ext-mgmt
• C. Add another block to IP pool ext-mgmt
• D. Select a pool size that is larger than 0

Answer: A

NEW QUESTION 5
Open the windows by clicking on the minimized at the bottom of the viewing area. Windows can be minimized by clicking on the [X], repositioned by dragging the title bar, and resized by using the handle at the lower right corner to customize the viewing area.
If you are required to access the devices to complete this scenario, the mouse cursor will use a hand symbol when moved over device icons. Clicking the icon will open a device terminal so you can interact with the hardware.
Open the Questions window and begin by clicking a question number. When you have completed answering all questions, click Done to continue.
Scenario
Use your UCS knowledge on Adapter errors ………………………………………configurations.

We are working on which server?

• A. 1
• B. 2
• C. 3
• D. 4
• E. 5

Answer: E

NEW QUESTION 6
Which three tasks can a user with the ext-lan-policy privileges perform? (Choose three.)

• A. Configure management interfaces on the fabric interconnect.
• B. Configure Ethernet pin groups.
• C. Configure management interfaces monitoring policy.
• D. Create/modify/delete vNIC/vHBA placement policies.
• E. Configure DNS providers and DNS domain.
• F. Specify the allowed range for virtual MAC addresses.
• G. Configure fabric interconnect system name.
• H. This privilege has full access to all operations.

Answer: BDF

NEW QUESTION 7
Which three statements about what occurs when a Cisco UCS -Series Blade Server connects to the SAN across a fabric interconnect that is enabled in Fibre Channel NPV mode are true? (Choose three.)

• A. The server ports in F Port mode are pinned to the NP Ports.
• B. The E Ports are pinned to the E Ports on the fabric interconnect.
• C. Zoning is deployed on the fabric interconnect.
• D. The fabric interconnect is not assigned a Fibre Channel domain ID.
• E. Traffic that is received on the server ports in F Port mode from the server side is pinned to the NPIV-enabled uplink ports on the fabric interconnect.
• F. The fabric interconnect must have the Fibre Channel uplink port connected to the upstream switch F Port in NPIV mode that performs the Fibre Channel forwarder function.

Answer: ADE

NEW QUESTION 8
Which two statements about the maintenance policy configurations available from the Cisco UCS Manager GUI are true? (Choose two.)

• A. A maintenance policy can be defined for the service profile associated to a server and for updating a service profile bound to one or more service profiles.
• B. A maintenance policy is used to configure a nondisruptive upgrade of the Cisco UCS Fabric Interconnects.
• C. A maintenance policy can defer the direct deployment of firmware images for components that use neither the host firmware nor the management firmware packages available in the Cisco UCS Manager, such as fabric interconnects and IOMs.
• D. A maintenance policy can deploy service profile changes immediately, when acknowledged by an admin user or automatically at the time specified in the schedule.
• E. A maintenance policy can be used only to apply nondisruptive service profile changes to servers.

Answer: BD

Explanation: Reference:
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/20/b_UCSM_GUI_Configura

NEW QUESTION 9
Refer to the exhibit.

Which two action do you perform on the remote switch before you run the commands? 9Choose two)

• A. Configure a minimum of eight links in the port channel.
• B. Configure the remote switch to use NPIV mode.
• C. Set port channel mode to on.
• D. Configure the remote switch for NPV.
• E. Enable the port-channel-trunk feature.

Answer: BC

NEW QUESTION 10
Which two statements about Cisco VM-FEX dynamic vNIC configuration and provisioning by using the Cisco UCS Manager are true? (Choose two.)

• A. Dynamic vNIC parameters are configured by using SNMP.
• B. Dynamic vNIC parameters must be configured manually before the virtual machine connects to its port group.
• C. Dynamic vNIC parameters are configured dynamically after the assigned virtual machine connects to the port group.
• D. Dynamic vNIC parameters are enabled by using the Fibre Channel Forwarder protocol.
• E. Dynamic vNIC parameters are configured by inheriting the port-group parameters of the associated virtual machines.

Answer: CD

Explanation: Reference: http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/mkt_ops_guides/513_n1_1/n5k_ops_vmfex.pdf

NEW QUESTION 11
Which three AAA protocols are supported for communication with external AAA providers? (Choose three.)

• A. TACACS+
• B. RADIUS
• C. AD
• D. LDAP
• E. ACS
• F. 802.1X

Answer: ABD

Explanation: Cisco UCS supports two methods to authenticate user logins: Through user accounts local to Cisco UCS Manager Remotely through one of the following protocols:
LDAP RADIUS TACACS+
Reference: https://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/141/UCSM_GUI_Configuration

NEW QUESTION 12
You must update your certificates after the name of a Cisco UCS Fabric Interconnect cluster changes. Which action do you take?

• A. Use the built-in default key ring certificate in Cisco UCS Manager.
• B. Regenerate the certificate manually.
• C. Request a new public-key certificate from the intermediate CA.
• D. Request a new root certificate from the root CA.

Answer: B

NEW QUESTION 13
Refer to the exhibit.

Which two media types can you mount from the KVM console? (Choose two.)

• A. ISO
• B. VHD
• C. VHDx
• D. IMG
• E. VMDK

Answer: AD

NEW QUESTION 14
You must implement a Dynamic FCoE topology that uses ECMP. Which ancillary technology do you use?

• A. OTV
• B. VXLAN
• C. FabricPath
• D. EIGRP

Answer: C

NEW QUESTION 15
Which two statements about the service profile configuration options in the Cisco UCS Manager GUI are true? (Choose two.)

• A. It can be generated automatically from the service profile template.
• B. It can be derived from the chassis discovery policy.
• C. It can be derived from the initial template or the updating template.
• D. It can be configured by cloning a virtual machine profile.
• E. It can be configured by using the chassis connectivity policy.

Answer: AC

Explanation: Reference: https://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/141/UCSM_GUI_Configuration

NEW QUESTION 16
You must upgrade a Cisco UCS -Series Server. Where must the Cisco UCS bundle image be located before you can begin the upgrade?

• A. the Cisco Integrated Management Controller memory of the server
• B. a USB drive connected to a Cisco UCS Fabric Interconnect
• C. a TFTP server accessible to the Cisco UCS Fabric Interconnect
• D. the flash file system of the fabric interconnect

Answer: C

Explanation: Reference:
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/firmware-mgmt/gui/21/b_GUI_Firmware_Man
ger.html#concept_1923688E7A2E46239DCAE363E4A3DE81

NEW QUESTION 17
When a configuration change requires a reboot, which policy specifies how Cisco UCS manager should proceed?

• A. host firmware policy
• B. local disk policy
• C. maintenance policy
• D. boot policy

Answer: C

Explanation: Use the Maintenance Policy to specify how Cisco UCS Manager should proceed for configuration changes that will have a service impact or require a server reboot. Values for the Maintenance Policy can be "immediate", "user- ack", or "timer automatic". The best practice is to not use the "default" policy, and instead to create and use Maintenance Policies for either "user- ack" or "timer automatic",
and to always have these as elements of the Service Profile or Service Profile Template definition. http://www.cisco.com/c/en/us/products/collateral/
servers-unified-computing/ucs-manager/whitepaper_c11-697337.html