we provide Pinpoint Cisco 642-980 exams which are the best for clearing 642-980 test, and to get certified by Cisco Troubleshooting Cisco Data Center Unified Fabric. The 642-980 Questions & Answers covers all the knowledge points of the real 642-980 exam. Crack your Cisco 642-980 Exam with latest dumps, guaranteed!
Q31. In order to fulfill the requirement to prevent the creation of end-to-end loops across a multihomed OTV network that connects two different data centers, what is the solution to this problem?
A. prioritize the transmission of STP BPDUs across the overlay
B. design the DCI connectivity as a hub and spoke
C. define a conservative TTL for all packets traversing the OTV network
D. enable AED on a per-VLAN basis between each OTV edge device with the same site ID
Answer: D
Q32. Which command is used to check for potential vPC configuration consistency problems?
A. show vpc brief interface
B. show vpc global config
C. show vpc consistency-parameters global
D. show vpc config
Answer: C
Q33. Which command displays the traffic statistics for a port channel interface?
A. show interface port-channel channel-number
B. show port-channel traffic
C. show port-channel usage
D. show port-channel compatibility-parameters
Answer: B
Q34. Refer to the exhibit.
When suspending or deleting VSANs, which three statements are true? (Choose three.)
A. You can delete only one VSAN at a time.
B. You must wait 60 seconds after you enter the vsan suspend command before you enter another command.
C. You must wait 120 seconds after you enter the vsan suspend command before you enter another command.
D. You can unsuspend only one VSAN at a time.
E. You can delete multiple VSANs as long as they are in the same domain.
F. You can delete multiple VSANs as long as they are in the same zone.
Answer: ABD
Q35. Which command would you use to check the status of your configuration synchronization peer?
A. N5K2# show switch-profile peer
B. N5K2# show config-sync peer
C. N5K2# show synch peer
D. N5K2# show peer status
E. N5K2# show switch peer
Answer: A
Q36. There is an ARP storm in VDC 1. Some users on VDC 2 notice that ARP is not resolving for their gateway on the Cisco Nexus core. What is the cause?
A. The ARP CoPP class committed information rate is exceeded, resulting in ARP loss in all VDCs.
B. The administrator has not correctly configured the ARP CoPP class in VDC 2.
C. The ARP traffic in VDC 1 is copied to the host ports in VDC 2, causing overutilization and output discards.
D. Because the ARP process in the default VDC (VDC 1) is responsible for processing ARP traffic for all VDCs, VDC 2 will be affected.
Answer: A
Q37. Refer to the exhibit.
A customer is having a problem getting NPV to work. What is causing the problem?
A. The core NPV switch port is not an F port.
B. The core NPV switch port is in a shutdown state.
C. The core NPV switch port is not configured on both ends.
D. The core NPV switch port is not configured on the other end.
E. The core NPV switch ports are in the wrong domain.
Answer: A
Q38. When using a Cisco Nexus 5500 and Cisco Nexus 7000 Series Switch, how can a port channel interface be configured?
A. Layer 3 interface
B. Layer 3 interface in non-admin VDC only
C. Layer 3 interface in admin VDC only
D. Layer 3 interface in VDC 1 only
Answer: A
Q39. Which two commands will show all the OTV edge devices and their MAC addresses in the local site? (Choose two.)
A. show otv overlay
B. show otv site
C. show otv vlan
D. show otv adjacency
E. show mac address-table
Answer: BD
Q40. Which two commands will show all the OTV edge devices and their MAC addresses in all sites in the overlay? (Choose two.)
A. show otv adjacency overlay
B. show otv site
C. show otv vlan
D. show otv adjacency
E. show mac address-table
Answer: AD