Our pass rate is high to 98.9% and the similarity percentage between our JN0-102 study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Juniper JN0-102 exam in just one try? I am currently studying for the Juniper JN0-102 exam. Latest Juniper JN0-102 Test exam practice questions and answers, Try Juniper JN0-102 Brain Dumps First.
P.S. Accurate JN0-102 questions pool are available on Google Drive, GET MORE: https://drive.google.com/open?id=1E1Dh477bEbi_EiAhCJBuRsk2_SYWpZfE
New Juniper JN0-102 Exam Dumps Collection (Question 2 - Question 11)
Q1. When you display the routing table by entering the show route command, what does the * indicate?
A. The route is a direct route.
B. The route was selected as active.
C. The route is a default route.
D. The route was learned using a dynamic routing protocol.
Answer: B
Explanation:
An asterisk (*) indicates that the route is both the active and the last active route. An asterisk before a to line indicates the best subpath to the route.
References: https://www.juniper.net/documentation/en_US/junos14.1/topics/reference/command-summary/show-route-detail.html
Q2. -- Exhibit --
[edit policy-options] user@router# show
policy-statementpolicyABC { term A {
from { protocol rip;
route-filter 192.168.1.0/24 longer;
}
then accept;
}
}
[edit protocols ospf] user@router# show exportpolicyABC; area 0.0.0.0 { interface ge-0/0/0.0; interface lo0.0;
}
-- Exhibit --
Referring to the exhibit, which two statements are true? (Choose two.)
A. The route 192.168.1.0/25 is accepted.
B. The route 192.168.2.0/24 is accepted.
C. OSPF routes will be exported into RIP.
D. RIP routes will be exported into OSPF.
Answer: A,D
Q3. Click the Exhibit.
Your Junos device is using the configuration shown in the exhibit. You notice that the 172.17.23.10/30 address is incorrect and should be 172.17.23.9/30.
What are two commands that would solve this problem? (Choose two.)
A. [edit interfaces]user@router# set ge-0/0/2.0 family inet address 172.17.23.9
B. [edit interfaces]user@router# replace pattern 172.17.23.10 with 172.17.23.9
C. [edit interfaces]user@router# rename ge-0/0/2.0 family inet address 172.17.23.10/30 to address 172.17.23.9/30
D. [edit interfaces]user@router# delete ge-0/0/2.0 family inet address 172.17.23.10
Answer: B,C
Q4. Which command do you use to show active alarms?
A. show hardware state
B. show system alarms
C. show chassis state
D. show services alarms
Answer: B
Q5. What is the default import routing policy for OSPF?
A. Accept all OSPF routes and install them into the inet.3 routing table.
B. Accept all OSPF routes and install them into the inet7.0 routing table.
C. Accept all OSPF routes and install them into the inet4.0 routing table.
D. Accept all OSPF routes and install them into the inet.0 routing table.
Answer: D
Q6. Which network mask is the equivalent of 255.255.248.0?
A. /20
B. /21
C. /22
D. /23
Answer: B
Q7. What is correct regarding the configuration shown below?
static route 0.0.0.0/0 qualified-next-hop 172.30.25.1 preference 7 next-hop 172.30.25.5
A. The next-hop 172.30.25.1 is selected because the address has the lowest value.
B. The next-hop 172.30.25.1 is selected because it is listed first.
C. The next-hop 172.30.25.1 is selected because it is the lowest protocol preference.
D. The next-hop 172.30.25.5 is selected because it is the lowest protocol preference.
Answer: D
Explanation:
The routes with a lower route preference are always used to route traffic. Preference 5 is the default preference for static routes.
References: https://www.juniper.net/documentation/en_US/junos15.1/topics/concept/routing-protocol-
static-security-route-preference-and-qualified-next-hop-understanding.html
Q8. -- Exhibit -- [editsnmp] user@router# show
communityCommunityA { authorization read-only; clients {
192.168.1.0/28;
}
}
trap-groupgroupA { categories {
link;
}
targets { 192.168.100.1;
192.168.200.1;
}
}
-- Exhibit --
Referring to the exhibit, what is the purpose of the targets section of the configuration?
A. It defines which devices will be sending traps.
B. It specifies where to send traps.
C. It defines the IP addresses of management systems that can access the device.
D. It specifies which devices can be polled for SNMP data.
Answer: B
Q9. Which two commands would you use to view OSPF routes? (Choose two.)
A. show ip route ospf
B. show ospf routes
C. show route protocol ospf
D. show route
Answer: C,D
Q10. Which statement is true about the routing table?
A. The routing table exists in the control plane only.
B. The routing table exists in the control plane and in the forwarding plane.
C. The routing table contains both active and inactive routes.
D. The routing table is stored on compact flash.
Answer: A
P.S. Easily pass JN0-102 Exam with Dumpscollection Accurate Dumps & pdf vce, Try Free: http://www.dumpscollection.net/dumps/JN0-102/ (405 New Questions)